How Far Apart are the Mounting Points on the Optronics TLL160RK?

Question

Question:

How far apart are the tll160rk mounting bolts, center to center? Replacing and need to match up with current holes! Thanks

asked by: John B

0

Expert Reply:

The mounting holes on the Optronics LED Combination Trailer Tail Lights # TLL160RK are 2 inches apart. I included a picture showing all the measurement for you to check out as well.

expert reply by: Lazer S

0

Optronics TLL160RK Measurements
(click to enlarge)

Answer 1

The Deka 16-14 Gauge Butt Connectors - 5 Pack, #05731-5 would be a great choice to allow you to wire up all of the lights you mentioned. The brown wire of the #TL16RK is a single wire that you'd need to run from one side of the trailer to the…

view full answer...

Answer 2

Electric brakes, like part #23-26-27, use 16 gauge wiring. However, we generally recommend using 10 gauge, like part #10-2-1, to connect to the brakes because of how far the wiring generally has to be run. So you need to use butt connectors large…

view full answer...

Answer 3

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How Far Apart are the Mounting Points on the Optronics TLL160RK?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching