How Thich is the Ball Platform on the Curt C24WR?

Question

Question:

How long of a ball shank do I need for C24WR?

asked by: Jonathan T

0

Expert Reply:

I spoke to a tech over at Curt and they confirmed the ball platform on their # C24WR is right at an inch thick. If you were looking for a ball to go with this, the Brophy # EH68C-C will be an 8,000 pound 2 inch ball option, and the Curt # C40007 will be a 10,000 pound 2 5/16 inch ball option.

expert reply by: Lazer S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 7

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Answer 10

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 11

The TireMinder i10 TPMS #TM38FR refreshes every 6 seconds. You will get a visual and audible alert when the monitor receives the signal from your tire sensor is either below your pressure or the temperature exceeds the maximum setting.

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

How Thich is the Ball Platform on the Curt C24WR?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching