Parts Needed to Install 7-Way and Brake Controller on 2019 Mitsubishi Outlander PHEV

Question

Question:

This kit lets me wire my PHEV Outlander for a flat 4 plug, good first step. My trailer is fitted with a 7 conductor plug, brakes, 12v and reverse lights not currently fitted, future upgrade How do I use this kit with the 7 wire plug? Is there a bundled kit that will allow me to use 4 or 7, depending on the trailer inserted?

asked by: Patrick M

1

Helpful Expert Reply:

To install 7-way trailer wiring on your 2019 Mitsubishi Outlander you'd need the part # C59496 that you referenced as well the part # ETBC7 which comes everything needed to convert it to a 7-way plus everything needed to install a brake controller and have the 12 volt accessory circuit active as well. This also gives a 4-way you can use as well. It gives option to have reverse light circuit wired in too in the future if you'd like also.

Then for a brake controller the part # TK63VR would be a great option as well. It uses an inertia sensor to determine how hard to apply the trailer brakes and also is very reliable.

expert reply by: Jameson C

1

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Parts Needed to Install 7-Way and Brake Controller on 2019 Mitsubishi Outlander PHEV

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching