How Many Jacks Come With The Bulldog Square Jack # BD182815?

Question

Question:

does this item come with the set of 2 jacks or just 1?

asked by: Jose T

0

Expert Reply:

The Bulldog Square Jack - Drop Leg w/ Spring Return - Sidewind - 26" Lift - 10,000 lbs # BD182815 is for a single jack. For a tandem jack application you will need to pair this jack with either the Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Planetary # BD183816 or Bulldog 2-Speed Jack - Drop Leg w/ Spring Return - Traditional # BD183903.

The Bulldog Sidewind Jack Crank Assembly # BD800090 is sold separately.

expert reply by: Bud M

0

Answer 1

When the Pro Series Square Jack #PS1400950376 is fully retracted it is 28 inches tall. When fully extended it is 54 inches tall. The outer tube is 4 inches square. If you are looking for some specific dimension let me know and I can determine what it…

view full answer...

Answer 2

The shaft on which the crank attaches to for the Pro Series Square Jack, #PS1400950376, measures 1 inch in diameter. I have also included a dimensional diagram for the jack for you to view.

view full answer...

Answer 3

I have attached the diagram with all of the dimensions of the Pro Series Square Jack - Drop Leg w/ Spring Return #PS1400950376 you are looking for. The Pro Series #PS1400950376 has a 10000lb weight capacity, is a direct weld on design, and includes a…

view full answer...

Answer 4

I spoke with my contact at Reese and he sent me dimensions of the Pro Series Jack, item # PS14009503676. I have included a drawing containing these dimensions for you to review. There is no owners manual included with these Jacks at this time. The…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...