What Tracks Do I Need for the Rhino-Rack Roof Rack for Thule and Yakima Tracks?

Question

Question:

I like the Thule rack but would also require the tracks to mount it to. Where can I obtain these and what is the additional cost ?

asked by: Alan P

0

Expert Reply:

The tracks you need for the Rhino-Rack Roof Rack for Thule and Yakima Tracks # Y01-140B-NT is the Thule Top Track Roof Mount System, 42" Long # THTP42. In addition to the tracks, # THTP42 includes drill bits, a flare-nut tool, and loctite silicone thread sealant.

expert reply by: Bob C

0

Answer 1

There are end caps on the Rhino-Rack Roof Rack for Thule and Yakima Tracks - 2 Heavy-Duty Crossbars #Y01-140B-NT that are tapered but the actual bar itself is not tapered so if you really wanted to cut them shorter you certainly could.

view full answer...

Answer 2

It looks like the jack on the trailer is a Reese swivel jack. The Fulton jack you referenced #FXP15W, should fit in its place no problem. Fulton and Reese are sister companies. However, the bolt holes are 3 inches on center. You will most likely…

view full answer...

Answer 3

I believe the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 you referenced would work for you. I went out into our warehouse and pulled one to measure the dimensions of the mounting flange and I believe it would work for you since you…

view full answer...

Answer 4

While there is a way to add a high-quality but cost-effective roof rack to your 2012 Honda CR-V with flush-mounted rails, there is not a way to mount the Tracker II rack top your vehicle as it was discontinued six years ago. The best option will be…

view full answer...

Answer 5

I do have an option for you but the photo you attached is a of a Thule Tracker FootBase which have since been discontinued. There are no longer parts available to use the Thule Tracker FootBase but you can still reuse the tracks you already have…

view full answer...

Answer 6

Yes the Rhino-Rack Roof Rack for Thule and Yakima Tracks #Y01-140B-NT that you referenced does fit the channels on top of your Leer camper shell directly. No other adapters would be needed.

view full answer...

Answer 7

The Rhino Rack #Y01-140B-NT includes the crossbars, the roof rack feet and the hardware necessary to mount the feet into the existing Thule or Yakima-compatible rails in the channel on your Leer camper shell. Everything shown in the photos I provided…

view full answer...

Answer 8

It sounds like you are looking for a set of crossbars to mount within the track system on a Leer Truck Bed Topper and if that's the case we have some great options. I recommend the Rhino-Rack Roof Rack for Thule and Yakima Tracks part…

view full answer...

Answer 9

You can indeed install a Yakima roof rack system on your Leer cap that features the Thule tracks. You will need to start with two of the Landing Pad 1 #Y00221, which are the pieces that will mount to the tracks to provide an attachment point for the…

view full answer...

Answer 10

The correct fit kit to use with the Thule Feet part #TH460R and your current Evo Square bars like part #TH712500 is actually the part #THKIT3101 for your Leer camper shell roof rack tracks.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...