Does Curt Assure Brake Controller Require Level Ground to Configure

Question

Question:

I am trying to setup my curt assure brake controller 51160. It states you have to be level to configure. I do not have anywhere level to configure. Will this be a problem? Also does this reconfigure every time you plug the trailer in? 2012 chevy colorado

asked by: Dave

0

Expert Reply:

It is recommended to run the configuration of the Curt Assure part # C49UR when you are level ground. I would try to find a parking lot near you that has a level surface and try it there. At worst you should be able to get it really close on unlevel ground but once you find level ground check it there as well.

You would not need to reconfigure it with every use. It will store setting unless you cut power to it.

expert reply by: Jameson C

0

Answer 1

The Curt Assure Trailer Brake Controller #C49UR will require the Universal Wiring Harness #C51515 to be hardwired in place of your current brake controller on your 1997 Dodge Ram 2500. I recommend the Tekonsha Prodigy P3 Trailer Brake Controller…

view full answer...

Answer 2

Brake controllers like the #C49UR Curt Assure aren't a vehicle-specific item. You can install a brake controller on just about any vehicle. What the installation will involve will depend on whether your E350 is equipped with a trailer connector…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 8

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 9

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 10

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 11

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Answer 12

Yes, when installing the knob for the Redarc Tow-Pro Liberty Brake Controller item #RED24FR you will want to remove any extra material behind the insert. I am happy the video was able to help you out. I have linked a couple of pictures from the video…

view full answer...

Does Curt Assure Brake Controller Require Level Ground to Configure

Continue Researching