Mounting Inserts for the Redarc Tow-Pro Liberty Brake Controller

Question

Question:

Hi, I just bought the Redarc Tow-Pro Liberty Brake Controller and I saw the video of the installation on the Subaru Outback 2020. I have an Outback 2020 XT so this is the perfect video for me, thanks! But when I pulled out the insert to install the brake controler switch, I was not sure if I had to remove all the excess of material behind it... did the guy in the video took the same that is with the Outback or I need to buy a special ? I can send some picture if required.. Thanks!

asked by: Matthieu

0

Expert Reply:

Yes, when installing the knob for the Redarc Tow-Pro Liberty Brake Controller item # RED24FR you will want to remove any extra material behind the insert. I am happy the video was able to help you out. I have linked a couple of pictures from the video to give you a still up close view. We have a couple of other mounting options for the control knob that can go inside inserts in your dash. The Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob item # 331-TPSI-001 which measures 1-1/4 by 1 inch. There is also the option of using the Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob item # 331-TPSI-002 for the more standard knock-out measuring 1-1/4 by 7/8 inch. I have linked a couple diagrams to show you the dimensions of these mounts.

expert reply by: Jerred H

0

Redarc Control Knob Mount
(click to enlarge)

Redarc tow pro installed
(click to enlarge)

Redarc Control Knob Mount
(click to enlarge)

Redarc tow pro knob
(click to enlarge)

Answer 1

To replace the UFP HD-1377 hub/drum assembly and your 10" electric trailer brakes you'll need the following parts: - 10" Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA - Trailer Hub and Drum Assembly - 3,500-lb Axles…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The Redarc Tow-Pro Liberty #RED24FR would be a great choice for your 2022 Jeep Cherokee Trailhawk. There are other options but this brake controller is my personal favorite. It is reliable and stays out of your way with only the knob showing in the…

view full answer...

Answer 4

The three items you mentioned are all that's needed to install the Redarc Tow Pro Liberty part #RED24FR in your 2016 Toyota 4Runner with the tow package: #RED24FR #331-TPSI-002 #RED49FR

view full answer...

Answer 5

Thanks for the pictures! I have exactly what you are looking for. We have a couple of mounting options for the control knob that can go inside inserts in your Subaru's dash. This will give you a clean factory look install. The Universal Mounting…

view full answer...

Answer 6

The trailer hitch that will be the least visible on your 2016 Lexus GX 460 is the Curt Class III Trailer Hitch Receiver #C13043. The end of the receiver on this hitch does not extend as far from the rear mounting holes as the receiver on the…

view full answer...

Answer 7

The Draw Tite hitch part #75685 that you referenced is a confirmed fit for your 2018 Lexus GX 460. It does come pretty close to the lower fascia on the rear of the vehicle so it touching it would not be too unusual. I attached a picture that shows it…

view full answer...

Answer 8

The Redarc Tow Pro Liberty #RED24FR is a really great brake controller choice for your 2020 Toyota Tacoma. All you need to install it is the harness part #RED99FR. This is by far the best value brake controller out there as you get a proportional…

view full answer...

Answer 9

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 10

To install the Redarc Tow-Pro Liberty Trailer Brake Controller #RED24FR you were looking at all you will need is the Plug-In Adapter #RED39FR. This will plug into the controller of the #RED24FR and then plug directly into the factory trailer brake…

view full answer...

Answer 11

The biggest difference between the two Redarc brake controllers is that the Tow-Pro Elite #RED44FR has a proportional control and user controlled mode you can switch between, while the Tow-Pro Liberty #RED24FR has just the proportional mode. The…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Mounting Inserts for the Redarc Tow-Pro Liberty Brake Controller

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching