Can I Use the TorkLift Cannon with a Weight Distribution Hitch

Question

Question:

Hello, the specs state to use weight distribution to utilize the upper capacities, but no recommendation is given for a torklift WD. I will be using this under a truck camper to get the hitch out, and connect to a 20 foot cargo trailer. This means any WD will go from trailer A frame to the hitch. Which WD should I use with the Cannon?

asked by: Ken

0

Expert Reply:

The weight distribution hitch you'll want to use will depend on the GVWR and tongue weight of your cargo trailer; you ideally have a WDH that the tongue weight of your trailer falls right in the middle of the range. Assuming that you tow the maximum that the Torklift Cannon # TLE1642 will allow (660-lbs TW/6600-lbs GVWR), something like the Curt Trunnion Style Weight Distribution System w/ Shank - 1K TW, 10K GTW # C24UR would be a good choice. This system will fit in the Cannon when you use the 2" sleeve reducer that is included. If your loaded tongue weight of the trailer is typically less than 500-lbs there might be a different system that could be used, so let me know if that is the case.

This WDH will allow you to tow the maximum allowable with the Cannon and give you reliable weight distribution that can be used on a cargo trailer. You may need to install some bolt/weld on chain hangers like the Chain Hangers for Reese Weight Distribution Systems - Bolt On # RP58305 if your cargo trailer frame is wider than 2-3/4" wide, which will give you a point on the trailer to connect the chains.

I've linked some review videos of these parts for you to check out.

expert reply by: Erik B

0

Answer 1

We have the TorkLift Cannon Hitch Extension for 3" Ford Super Duty Factory Hitch #TLE1642. You will not be able to use an extension of this length with a rise hitch adapter. This is because the 42" hitch extender has to be secured with…

view full answer...

Answer 2

There is one extender that will work with the 3 inch factory hitch on your 2017 Ford F-350 Super Duty, the TorkLift Cannon Hitch Extension, and it comes in three different lengths: 36" Long #TLE1636, 42" Long #TLE1642 and 48" Long…

view full answer...

Answer 3

Based on all of the information I was able to find on your 2018 Ram 3500 DRW with the max tow package your truck should have a 2-1/2" trailer hitch receiver. For a 2-1/2" receiver you will need the Curt Hitch Extension and Reducer for…

view full answer...

Answer 4

It sounds like you have a trailer hitch receiver already installed and need to add a second trailer hitch receiver for a double receiver to allow for the extension and tongue weight of your horse trailer. Because you don't have the factory hitch…

view full answer...

Answer 5

The tongue weight capacity of the TorkLift SuperTruss Hitch Extension 36" part #TLE1536 is 200 lbs if you have the Hero (15K) and 650 lbs if you have the Original (20K) or Magnum (30K). Therefore, if you have the Hero you would likely not be…

view full answer...

Answer 6

Your 2019 Ram 3500 4X4 diesel with the 8' bed and factory running boards under the cab. You have two options, depending on your vehicle's options. If you have the 8' bed with a fixed board under your cab with factory installed hitch, you…

view full answer...

Answer 7

The TorkLift Locking FastGun Turnbuckles for Frame-Mounted Tie-Downs - Stainless Steel - Black - Qty 4 #TLS9529-2-LK comes with the keyed alike locks, so one key will work for all 4 locks. You will get 4 keys, but you can use 3 of them as spare…

view full answer...

Answer 8

The part #TLS9013 tie downs are considerably shorter than the frame mounted options like the #TLS9529-2-LK. If you added chain links and did it in a safe way maybe you could use them for a frame mounted setup but I would strongly recommend you go…

view full answer...

Answer 9

Yes, the Happijac Qwik-Load turnbuckles are very similar to the Torklift Turnbuckles like the #TLS9529-2-LK so they would work fine.

view full answer...

Answer 10

For your 2010 Dodge Ram dually, short bed, with factory hitch and without full length running boards the correct tie downs from Torklift are the part #TLD2120 and #TLD3109. Since you have a dually you do also need the relocation kit part #TLA7004…

view full answer...

Answer 11

I do have options for you but you cannot install two of part #C45796 together to get a total of 36". Doing so would completely diminish your trailer hitches weight capacity. The most cost effective solution I have for you would be to use part…

view full answer...

Answer 12

With a flat towing setup like you mentioned you won't see any vertical weight on the tow vehicle hitch since there is no weight to support. It would be all horizontally pulled weight like you mentioned. From what we know about the Torklift hitch…

view full answer...

Can I Use the TorkLift Cannon with a Weight Distribution Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching