Heavy Duty Trailer Hitch that Fits 2000 Chevy Silverado 3500 Cab and Chassis

Question

Question:

Hello I am looking for a trailer hitch for a 2000 Chevy 3500 cabin chassis Dooley truck I believe it will accommodate the 34 inch wide rail to rail of the frame like a normal 3500 but I do not want the bolted version I would like the welded version for the heavy duty hitch I just don’t know what that part number is? I’m also looking for a minimal Thank you

asked by: Jeremy

0

Expert Reply:

We do have bolt-on hitches that fit your 2000 Chevy Silverado 3500 cab and chassis like with the Draw Tite part # 41947 which could be welded on if you wanted.

expert reply by: Jameson C

0

Answer 1

The Ultra Frame Trailer Hitch Receiver #41947 has an adjustable cross-tube that allows the receiver to be moved into a variety of height adjustments. There are 3 locations on that this hitch can be mounted in (see attached photo diagram): Height from…

view full answer...

Answer 2

The 2017 GMC Sierra 3500 cab-and-chassis is a confirmed fit for the Draw-Tite Ultra Frame Trailer Hitch #41947 so long as the truck frame width dimension is 34-inches from outside edge to outside edge. This frame dimension requirement applies to all…

view full answer...

Answer 3

Since you have a 34 inch wide frame we may have something that could work with a bit of fabrication on your part. 34 inch wide frames (measured from outside to outside) is a very common frame width for cab and chassis trucks. Check out the part…

view full answer...

Answer 4

Yes we do, it can be found listed as part #41947 on our site and is confirmed by Draw-Tite to fit your 2005 Chevrolet Kodiak C5500 Chassis with a Motorhome on it.

view full answer...

Answer 5

I have a universal hitch that will fit your Gulf Stream and provide you with the needed 10,000 lbs towing capacity but it must be welded on. It is the Class V Universal Weld-on Receiver Hitch item #15901. None of the bolt on hitches have a capacity…

view full answer...

Answer 6

Both the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 and Draw-Tite Ultra Frame Trailer Hitch Receiver #41938 are a confirmed fit for you 1969 Chevrolet K10 as long as you have an 8 Foot bed and both options will require some drilling for the…

view full answer...

Answer 7

I am going to need a bit more information in order to make a good recommendation. Is your 2010 Ford E450 a Cab and Chassis style or an RV cut-away. I spoke with my contact at Cequent, and they said that what you would have to do to determine if a…

view full answer...

Answer 8

I reached out to Draw-Tite and found that the distance from the frame mounting point to the top of the receiver at the lowest setting is 10-5/16". Keep in mind, the Ultra Frame Trailer Hitch Receiver #41947 is only confirmed to fit C/K series…

view full answer...

Answer 9

Draw-Tite custom-fit Class V hitch #41947, which fits trucks with an outside-to-outside frame width of 34-inches, can be installed at any of three heights, thanks to the multiple holes in the two frame brackets. I can give you these heights…

view full answer...

Answer 10

The horizontal mounting plate that mounts to the frame of your vehicle on the #41947 is 2-13/16" wide and the mounting plates themselves are 11-9/16" tall. The holes on the horizontal mounting plates are 3/4" and 1-1/4" in…

view full answer...

Answer 11

The width of the Ultra Frame Trailer Hitch Receiver part #41947 is 30-1/2" from the outside of each side plate. If you subtract the thickness of the plates you're looking at around 30" from end to end on the crosstube.

view full answer...

Answer 12

Draw-Tite trailer hitch #41947 is a custom fit hitch designed for specific vehicles and should not be used on any applications it was not designed for. The trucks it does fit on would have approximately 37 inch frames measured from outside to…

view full answer...

Heavy Duty Trailer Hitch that Fits 2000 Chevy Silverado 3500 Cab and Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching