Availability of Taskmaster 4.80/4.00-8 Tire Without Wheel

Question

Question:

Question on AS4808B4WS product: This part number is for tire + rim. I need this exact tire that comes on the rim for AS4808B4WS but WITHOUT the rim. What is the part # for that or how can I order that from you? Thank you

asked by: Todd V

0

Expert Reply:

We don't offer a Taskmaster 4.80/4.00-8 Load Range B tire without the rim, but we do offer a Kenda tire with the same load range as part # AM10002. The tire has a 590 lb per tire/ 1180 lbs capacity per axle.

I've linked to a description video featuring the # AM10002 tire.

expert reply by: Mike L

0

Answer 1

When it comes to the 4.80/4.00-8 trailer tire we do not carry a 2 ply load range A tire only. The closest that we have is The Kenda K371 Bias Trailer Tire - 4.80/4.00-8 - Load Range B #AM10002, and the Load Range C #AM10004. The load range B has a…

view full answer...

Answer 2

When going to a larger trailer tire size the biggest concern will be that you have enough clearance above the tire for additional height. The height difference between the two sizes you have would be a little over 2 inches so you would have 1 inch…

view full answer...

Answer 3

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 4

For that size tire, 4.80 X 8, I recommend the Kenda tire, #AM10004. This tire has the Load C rating and fits the 8 inch x 3-3/4 inch rim. Using the heavier load range could extend the life of this tire. The Kenda tire is a bias tire that tend to run…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...