Locating Brake Controller Connector on 2013 Toyota Tacoma with Factory Tow Package

Question

Question:

My 2013 tacoma has the seven pin plug and is tow ready, however there is no brake controller plug under the dash. Can I hard wire this in and can you send a wiring diagram on how to install it. It came with an adapter from toyota but I could not find the mate under the dash above the emergency brake pedal, I have a prodogy controler which I used on my frontier and it worked great. Hoping to hear from you soon. Your videos are very helpful. Thanks for your time.

asked by: Carmin M

0

Expert Reply:

Since your 2013 Toyota Tacoma has a factory tow package, including a 7-way connector at the back bumper, it will have a brake controller connector.

While it is usually visible above the emergency brake pedal, it may sometimes be taped or zip-tied to other wiring. You can try checking further up under the dash panel. If not there, the connector may be tucked in behind the left hand kick panel. Please refer to the attached photo.

The Tekonsha installation instructions for the P2, part # 90885 and wiring adapter # 3040-P. These indicate the need to ground the white wire (with ring terminal) to the vehicle chassis. It is usually easiest to do this with the kick panel removed so I suggest temporarily removing this part to both locate the harness/connector and select a suitable spot to secure the ground wire.

In case you need it, we offer a hardwiring kit for brake controllers, part # 5506. I have also linked the instructions for part # ETBC7, which will be helpful if you do choose to hard wire your controller.

expert reply by: Adam R

0

click to enlarge

Answer 1

Helper springs is a general term that can be applied to all suspension enhancement products. So what it comes down to is jounce style springs versus air bags. Jounce style springs are excellent for the same kind of load all the time, such as towing…

view full answer...

Answer 2

The 2015 Toyota Tacoma is part of the third generation of this vehicle and the location of the brake controller connection port is behind the left kick panel, near the emergency brake pedal. Please refer to the linked video at the :20-second mark…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

I went out into our warehouse and measured the distance from the ratchet mechanism to the e-track fastener of the Snap-Loc E-Track Tie-Down Strap #SLLS28RER and found that it measures 7-1/2 inches.

view full answer...

Answer 5

The 3-1/8 inch dimension on the CE Smith U-Bolt #CE15503A that you referenced is indeed taken from inside to inside on the posts. I have attached an image to assist. It will work great for your 3 x 3 inch trailer frame.

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

I can help you out, no problem. What you are going to want to look at is the towing capacities of the truck. You need to know the gross combined weight rating. This is the most the vehicle, including cargo and occupants, plus the trailer can weigh.…

view full answer...

Answer 8

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 9

You mention a 7-round plug and I just want to verify there are six flat pins in a circular pattern with a round pin in the center. You can use the Brake Controller 7 and 4-way Installation Kit - 10 Gauge (part ETBC7). There are videos on the product…

view full answer...

Answer 10

I looked up your 2013 Toyota Tacoma TRD Sport and everything I found says that you have a 6,400 lb towing capacity. That would be more than enough for your 1984 Stingray that weighs 2,050 lbs. If you were in need of a trailer hitch the Draw Tite…

view full answer...

Answer 11

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 12

Both the Dexter Electric Trailer Brake Kit #23-47-48 and the Electric Trailer Brake Kit #AKEBRK-2 are excellent options to replace the brake assemblies on your 2009 Palomino Pony pop-up camper. A lot of the Dexter Axle kit price comes from the name…

view full answer...

Locating Brake Controller Connector on 2013 Toyota Tacoma with Factory Tow Package

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching