Recommended Replacement Handle For Older Fulton K1550 Brake Winch

Question

Question:

Will this handle fit bolt on, and work to turn my Fulton K1550? I am wasting a stupid amount of time trying to find an 11inch replacement handle that will work, so I figured I better ask someone. Original Part # I found listed was 2461S01, but it is nowhere in existence. Any help would be appreciated. Thank You

asked by: Leo D

0

Expert Reply:

I reached out to my contact at Fulton and confirmed that the Replacement 11" Long Winch Handle for Fulton Single-Speed Winches # F501101 you were looking at is the correct replacement for your older Fulton K1550.

I included a video of the # F501101 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this…

view full answer...

Answer 3

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although…

view full answer...

Answer 4

Hey Jim! The Taskmaster and Westlake tires, like the Taskmaster ST235/75R15 Off-Road #TA45RR and Westlake ST235/75R15 Off-Road #WST54FR you were looking at, are made in China. A lot of people tend to shy away from trailer tires made in China but…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 7

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 8

It looks like your MORryde ALLTREK 4000 Shock Absorbing Equalizers #MR89DR are longer than your previous equalizers were because your leaf springs are way too close to each other. The shackles should be creating more of a "W" shape instead…

view full answer...

Answer 9

A 4,000 lb rated axle leaf spring like the part #e22YR would be a great option for your 2021 Keystone 26RB travel trailer. It would give you a little more capacity to help with the additional support you need on the one side of the trailer. It would…

view full answer...

Answer 10

The DeeMaxx Disc Brake Kit - Maxx Coat/Stainless - 3,500 lbs #DE46YR uses stainless steel calipers and a Maxx coating on the hub and rotor. This Maxx coating is a special coating made by DeeMaxx and has a 1,000 hour salt-spray rating, which is pretty…

view full answer...

Answer 11

Hey Ronald, thanks for reaching out! The correct replacement EZ Lube hub and drum assembly for your Shur Trac Trailer is the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K. Our fitguide is geared more towards vehicles and…

view full answer...