Picture of Gorilla-Lift Utility Trailer Tailgate Lift Assist Installed on Bifold Ramp Trailer

Question

Question:

Is there video or some photos showing this. Im thinking I have asked the wrong question though I asked about split gate but what I actually have is a bi-fold rear ramp.. so again, any video or pictures available?? thank

asked by: Roger W

1

Helpful Expert Reply:

We don't have a video of the # GL1 installed on a bi-fold trailer ramp but I did attach a picture we got from a customer who installed it on a bi-fold ramp setup for you to check out as well.

expert reply by: Jameson C

1

Bi Fold Trailer
(click to enlarge)

Answer 1

Thanks for reaching out! When you install the Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1 there is a trial and error type of section where you use S hooks to hook onto different points of your trailer ramp so you can test out…

view full answer...

Answer 2

In order for the Gorilla-Lift Utility Trailer Tailgate Lift Assist #GL1 to work properly it needs to install on trailer side rails that are totally horizontal and not sloping down. The height of the rails needs to be 12 to 24 inches from the bed of…

view full answer...

Answer 3

The Gorilla-Lift Utility Trailer Lift Assist you'd looked at (as are all the ones we offer) require that top of the trailer sides be between 12-14 inches above the trailer floor and the tailgate itself be 4-6 feet above the trailer floor. If…

view full answer...

Answer 4

If the side rails of your trailer are between 12 and 24 inches above the bed the Gorilla Lift part #GL1 would fit and work well. The tailgate then has to be between 4 and 6 feet in height above the trailer bed when up. So if your tailgate/ramp is…

view full answer...

Answer 5

When installing the Gorilla-Lift Utility Trailer Tailgate Lift Assist #GL1 you will want to attach the cable to the inside portion of the gate (closest to the trailer). This is simply because you want to have it secured to the stationary side of…

view full answer...

Answer 6

While the Gorilla-Lift Utility Trailer Tailgate Lift #GL1 that you referenced is only available in yellow, it is possible to the paint the outer housing of the tailgate lift. I spoke with my contact at Gorilla-Lift and she confirmed that the…

view full answer...

Answer 7

To incraese the tension on your Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable part #GL1 the connection points on the ramp should be mover higher on the ramp. Move it up and check for assist and just set it to your preference. Once you…

view full answer...

Answer 8

I attached a page from the install instructions for your Gorilla Lift Tailgate Assist #GL1 that covers how to lower the spring tension.

view full answer...

Answer 9

The Gorilla-Lift Utility Trailer Tailgate Lift Assist part #GL1 is designed for tailgates no more than 300 lbs. There is not an option to upgrade the weight capacity nor is there a lift assist for a heavier tailgate. This would be he limit for a…

view full answer...

Answer 10

Here's what I'd recommend. If you have an exposed portion of the hitch crossbar to work with, use the #18136 no drill bracket. This fastens to the hitch crossbar using an included pipe clamp. You'll also use the #PK12711U…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I do have an option for you but the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate part #VGD-10-4000 does not have a spot for the factory backup camera. Therefore you would either need to find a way to mount this yourself, go without, or…

view full answer...

Picture of Gorilla-Lift Utility Trailer Tailgate Lift Assist Installed on Bifold Ramp Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching