Weight Capacity of Gorilla-Lift Utility Trailer Tailgate Lift Assist

Question

Question:

What is the rating of the springs that come with Gorilla Lift? Are they 90#, 110# or more? Can I order heavier springs?

asked by: Michael W

0

Expert Reply:

The Gorilla-Lift Utility Trailer Tailgate Lift Assist part # GL1 is designed for tailgates no more than 300 lbs. There is not an option to upgrade the weight capacity nor is there a lift assist for a heavier tailgate. This would be he limit for a tailgate assist. If used on a heavier tailgate, it would still provide some assistance but the tailgate would likely still drop when let go of.

expert reply by: Conner L

0

Answer 1

Thanks for reaching out! When you install the Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable #GL1 there is a trial and error type of section where you use S hooks to hook onto different points of your trailer ramp so you can test out the…

view full answer...

Answer 2

We don't have a video of the #GL1 installed on a bi-fold trailer ramp but I did attach a picture we got from a customer who installed it on a bi-fold ramp setup for you to check out as well.

view full answer...

Answer 3

When installing the Gorilla-Lift Utility Trailer Tailgate Lift Assist #GL1 you will want to attach the cable to the inside portion of the gate (closest to the trailer). This is simply because you want to have it secured to the stationary side of the…

view full answer...

Answer 4

To incraese the tension on your Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable part #GL1 the connection points on the ramp should be mover higher on the ramp. Move it up and check for assist and just set it to your preference. Once you…

view full answer...

Answer 5

We've checked the part number you gave us before and the replacement for it is the part #T4750820 which is for disc brakes. This one does come with a reverse lock out solenoid. If it has rust all over it I'd consider just replacing the entire…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...