Hidden Hitch for a 2021 Tesla Model 3

Question

Question:

Hello, will this receiver mount to a stock factory installed Tesla hitch, or would that hitch need to be replaced with a complete Stealth hitch? Thank you, I’m looking at a 2021 Model 3

asked by: Bob P

0

Expert Reply:

The Stealth Hitches Hidden Rack Receiver part # 391TES317 is what you'll need to add a hidden trailer hitch to a 2021 Tesla Model 3. We do not have any options for factory hitches unfortunately.

expert reply by: Conner L

0

Answer 1

I'm sorry to hear about your receiver accessory! Yes! We do carry the replacement you need for your Stealth Hitch #391AUDQ818T. The replacement 2" receiver tube you need is the Replacement 2" Receiver Attachment for Stealth Hitches Rack…

view full answer...

Answer 2

Figuring out what color wire goes to what function is sometimes quite confusing. I have attached a diagram which covers both the most common wire colors designated for a seven pin trailer connector and a seven pin vehicle connector, referencing the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Hidden Hitch for a 2021 Tesla Model 3

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching