Does Kodiak Disc Brake Kit K2HRCM1337-9DAC Include Oil Bath Caps?

Question

Question:

P/N K2HRCM1337-9DAC disc brake conversion kit. Does this kit include the plastic outer hub clear screw on caps wet hub? if not, what is the part number? Thnkx

asked by: Joseph J

0

Expert Reply:

The Kodiak Disc Brake Kit - 13" Hub/Rotor - 8 on 6-1/2 - Dacromet - 7,000 lbs # K2HRCM1337-9DAC you were looking at includes the two clear plastic oil bath caps you mentioned, so you will not need to purchase them separately.

You will however need to purchase the bearings, and grease seals separately as they are not included. The # K2HRCM1337-9DAC uses inner bearing # 25580, outer bearing # 02475, and oil bath seal # RG06-090.

I included a few videos of the # K2HRCM1337-9DAC for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Yes, using oil bath hub seals #10-63 will work with the Kodiak disc brake kit you ordered, #K2HR79E. The kit already has the oil caps so you wouldn't need those. The brake kit does not include the bearings. You would need 2 of #25580 and 2…

view full answer...

Answer 2

That's tire cupping. When you have cupping wear on a tire it is from the tire bouncing on the road. You will want to check the air pressure in the tire and make sure you are running the maximum air pressure that is indicated on the tire.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...