Dimensions Of UWS Aluminum Tool Tray UWS060059

Question

Question:

It has 2 different sizes posted. UWS Aluminum Tool Tray for Extra-Wide Crossover Style Toolbox Item # UWS060059 Is it 26 1/2 or 24 1/2

asked by: David

1

Helpful Expert Reply:

The overall dimensions of the UWS Aluminum Tool Tray # UWS060059 are 26-1/2" Wide, 16" long, and 1-1/2" deep including the lip. The INSIDE dimensions for interior storage are 24-1/2" Wide, 16" long, and 1-1/2" deep. I have attached a diagram showing these dimensions for you.

expert reply by: Andrew N

1

Dimensions Of UWS060059
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I attached a picture that shows the proper position of shackles and equalizers on trailer suspension. Sometimes the shackle will flip up but if you jack up the trailer by the axle that's got the shackle flipped you can usually get it to flip back…

view full answer...

Dimensions Of UWS Aluminum Tool Tray UWS060059

Product Page this Question was Asked From

Continue Researching