Is There a Junction Box and 7 Way Connector Available With a Coiled 7 Way Instead of Straight

Question

Question:

do you sell item # HS381-9000 with a coiled cable?

asked by: John N

0

Expert Reply:

I may have a solution for you, but there is not a Junction Box with 7 way connector like the # HS381-9000 available with a coiled connector. However you could use the junction box from the kit # HS381-9000 and then add a coiled 7 way like the Bargman 7-Way, RV-Style Connector w/ 6' Long Coiled Cable - Trailer End # WG54006-043 to create your own junction box and 7 way that would work in the same manner; it'll just be a tiny bit of extra work making the initial connections since they're not all one piece.

expert reply by: Erik B

0

Answer 1

CR Brophy, the manufacturer of the #HSSF tie downs did not test fit on the 2006 Toyota Tundra, so they can neither confirm or deny the fit. I was told that if the bed is single walled and the lip under the bed side is at least 2 inches wide, the tie…

view full answer...

Answer 2

In order to attach a Starcraft Truck Bed Camper to a standard trailer connector you will need to remove the existing trailer connector and replace it as I am not aware of any adapter to use a standard trailer connector. For this, I recommend the…

view full answer...

Answer 3

What you can do is to use the Quick FixTM 4 Pole Flat Car and Trailer Ends, #48195, and not use one of the pins since you only have three wires that need to be connected. You can then use the wire you need inside of them as needed. The wires that run…

view full answer...

Answer 4

If you have a 2-1/2 inch hitch installed on your truck then you can use a hitch extender like the Curt part #C45048 which can give you from 24 to 34 inches of extension. You should note that when you use this extender the towing capacity is 6,000…

view full answer...

Answer 5

I have a good solution for you and while it isn't nearly as attractive as the Thule part #TH500XTB the Buyers Products Over-The-Cab Truck Bed Ladder Rack part #3371501150 will get the job done the easiest out of the options available. Check out…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...