Trailer Wiring Harness for Snowmobile Trailer

Question

Question:

I have a two place tilt bed snowmobile trailer and I cant find an all new wiring harness for it. Its a triton trailer, can you guys help me?

asked by: Ryan M

0

Expert Reply:

We have numerous trailer wiring harnesses you can use for your snowmobile trailer, but none specifically for a Triton trailer. You just need to choose from if your trailer needs a 4-way or 7-way, and there are 7-ways with insulated cable which is great for a snowmobile trailer.

- 4-Way: Hopkins Endurance Easy-Pull Harness # HM38134

- 7-Way: Bargman 7-Way, RV-Style Connector with Heavy Duty Insulated Cable - 6 Ft # 54006-057 or 8 Ft # 54006-058

I have added links below to some video reviews for you to check out as well.

expert reply by: Kyle S

0

Answer 1

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 2

For your wiring, you will need to test your wire functions to know which one connects where. I recommend using a 12v battery and simply connecting the negative terminal to the trailer frame and then connecting the power to each wire at the connector…

view full answer...

Answer 3

Standard 4-pole trailer wiring uses flat-style connectors, like part #W787268 which is a trailer-side connector and part #HM48044 which is the mating vehicle side connector. On these items and on the 16-gauge bonded 4-pole wire #16-4B-1 you…

view full answer...

Answer 4

Yes you should! You are on the money with what you need, a wishbone-style 4-way wiring harness for your trailer. With this style, the white is ground, yellow is left turn/brake, green is right turn/brake, and the two brown wires are the running light…

view full answer...

Answer 5

You're on the right track! If you're wanting to install a new 4 way connector on your snowmobile trailer you can use the 35-ft 4 way Trailer Wiring Harness #A35W42B. This is a wishbone style harness that comes with the tail light wiring…

view full answer...

Answer 6

The blue wire jacket on the Bargman 7-Way, RV-Style Connector w/ 8' Heavy Duty Insulated Cable part #54006-058 has an outer diameter of 0.6".

view full answer...

Answer 7

For a similar wiring harness that is made in the USA that has been confirmed to fit your 2006 Toyota Tacoma you would want the part #C55513.

view full answer...

Answer 8

The orientation of the grease hole on the wet bolts of the Dexter Heavy Duty Suspension Upgrade Kit #K71-358-00 does not matter. When you go to install this you don't have to worry about that at all.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...