What is the Overall Height from Mounting Bracket to Top of Stromberg Carlson Part # JET-5000

Question

Question:

What is overall height from mounting point to the top of jack?

asked by: George

1

Helpful Expert Reply:

The mounting plate on the Stromberg Carlson Electric Trailer Jack # JET-5000, is 23 inches below the top of the motor housing.

Check out the attached video.

expert reply by: Adam R

1

Answer 1

You will need a 12V battery for the Stromberg Carlson Electric Trailer Jack Part #JET-5000. The amperage draw for this jack at full load is 25-amps, so that is what I would want to know when shopping for a battery.

view full answer...

Answer 2

The Stromberg Carlson Electric Trailer Jack #JET-5000, uses the standard mounting bolt pattern, 3 inches apart on center, so you should have no problem using the existing holes on your 2015 Jayco trailer. I have included a short installation video…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 6

Your 2008 Chevy HHR should have a set of rails on the roof that run from front to back. Which means we have the Rhino Rack part numbers #RRVA106B-2 and #RRSX100 as a confirmed fit, but the kit you mentioned is not a fit.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Slipper Springs like #e33SR do not use a bolt and bushing for the open eye end of the spring. It connects directly to the hanger using a slipper spring hanger kit.

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 11

Blue Ox has base plate kits that fit your 2023 GMC Yukon XL with the part #BLU54VR which fits the AT4 models with 4L and the part #BLU58FR which fits the non-AT4 models. While we haven't had the chance to shoot an install video for either of…

view full answer...

Answer 12

Yes we have a 14 inch version of the Aluminum Viking Series Valhalla trailer wheel with the part #AX02455545BMFL. This is 5-1/2 inches wide and has the standard 5 on 4-1/2 inch bolt pattern that 14 inch trailer wheels have. I attached a picture of…

view full answer...