Does the Titan BrakeRite EHB Adapter for Ford/Chevy Integral Brake Controllers Fit a 2013 GMC Sierra

Question

Question:

Will this work with the 2013 models?

asked by: Jared W

0

Expert Reply:

If you have a Titan BrakeRite EHB actuator # T4813102 and your truck has the integrated brake controller then using the adapter # T4845900 will work for your 2013 GMC Sierra.

expert reply by: Michael H

0

Answer 1

I checked on Ford truck message boards and the most common two reasons the Trailer Disconnect Warning comes on is either that there is corrosion or water in the trailer connector, there is a short on the wiring behind the trailer's connector or…

view full answer...

Answer 2

The Titan BrakeRite EHB Electric-Hydraulic Actuator for Disc Brakes part #T4813100 will need to receive power from a 12 volt battery with a 40 amp circuit breaker like part #9510 placed 6" from the positive battery terminal. I have attached a…

view full answer...

Answer 3

If the controller is working fine with one trailer and not with the other then the problem is most likely with the trailer and not the truck. I would start by checking all of the ground connections on the trailer, especially the ground at the coupler…

view full answer...

Answer 4

The #T4845900 should work just fine on your BrakeRite SD. The connectors you sent in a picture of look to be the matching ones. That being said you could cut off the connectors and then hardwire the blue and white wires to the system like in the…

view full answer...

Answer 5

For your 2012 Ford F-150, all you should need to be able to use your OEM brake controller with your Titan EOH brake actuator, is the: -Titan BrakeRite SD Adapter for Ford/Chevy Integral Brake Controllers #T4845900. This adapter is compatible with…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...