What Type of Lug Nuts Does Phoenix USA QuickTrim Hub Cover for Trailer Wheels # QT545C Fit

Question

Question:

What type of lug nut is the most compatible with: Phoenix USA QuickTrim Hub Cover for Trailer Wheels - 5 on 4-1/2 ?

asked by: Phil G

1

Helpful Expert Reply:

The Phoenix USA QuickTrim Hub Cover for Trailer Wheels # QT545C that you referenced was designed for 1/2 inch lug nuts like the # 12CLN.

expert reply by: Jameson C

1

Answer 1

Yes, the Phoenix USA QuickTrim Hub Cover #QT545C will fit your 1/2" acorn style lug nuts. They are specifically designed to fit this style but also work with many open ended lug nuts as well.

view full answer...

Answer 2

The #QT545C hub cover is 3-3/4 inches deep, from the surface that touches the wheel to the end of the inside face of the cap. They should fit over your bearing buddies.

view full answer...

Answer 3

It sounds like you need the QuickTrim Trailer Hub Cover #QT545C. Just to be sure this is designed for 5 on 4-1/2 inch bolt patterns and has an outside diameter of 6-3/8 inches.

view full answer...

Answer 4

Gently prying the QuickTrim Trailer Hub Cover #QT545C would be the best way to remove it from a wheel. You could use a slot screw driver to do this. You would want to slide the tip of the screwdriver between the cover and the wheel and then use a…

view full answer...

Answer 5

To install the QuickTrim Trailer Hub Cover, part #QT545C, you would want to line up the lug nuts and apply firm pressure with your hand to snap the cover into place. You could also lightly use a rubber mallet after the cover is lined up in place.…

view full answer...

Answer 6

I checked out the lug nut torque chart you mentioned and the sizes you see are for the diameter of the stud that the lug nut is attached to. Lug Size Ft/Lbs Torque 1/2" 90-120 9/16" 120-140 5/8" 140-160 We'd have to recommend you…

view full answer...

Answer 7

You should be able to use the Americana Trailer Wheel Lug Nut #AM26NR. This fits 1/2" - 20 studs so just make sure that's what you have prior to ordering. You can verify this by measuring the diameter of your studs as the thread count should…

view full answer...

Answer 8

The guy you were speaking with was telling the truth. If the Bearing Buddies are overfilled, you will indeed blow out the grease seal. The excessive pressure will push the grease out through the rubber portion of the seal. Using a double lip grease…

view full answer...

Answer 9

Yes, the Phoenix USA QuickTrim Hub Cover part #PXQT545BHS will fit the acorn style (closed end) 1.38" tall lug nuts on your trailer. They are actually designed specifically for this type of lug nut but work with most open end versions as well. I…

view full answer...

Answer 10

I have attached a photo of how a breakaway system should be wired. If you would please, check the brake output wire on the trailer where the breakaway switch is spliced in. This is shown as the letter A in the attached photo. If something were to…

view full answer...

Answer 11

All you have to do is follow the steps that you took to select and save each trailer setting on the Prodigy P3 #90195. Just hold down the boost button for 2 seconds until the "Select" menu comes up, scroll to the desired trailer, the press…

view full answer...

Answer 12

If the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #QT545C will fit depends on the dimensions of the grease caps you have. The diameter of the interior at its narrowest point (nearest to the outside) is right around 2-1/4-inches, the depth…

view full answer...