Will Phoenix USA QuickTrim Hub Cover Fit Acorn Style Lug Nuts

Question

Question:

Will the Phoenix QuickTrim Hub Cover PXQT545BHS fit over closed end lug nuts measuring 1.38inch tall?

asked by: Nick

0

Expert Reply:

Yes, the Phoenix USA QuickTrim Hub Cover part # PXQT545BHS will fit the acorn style (closed end) 1.38" tall lug nuts on your trailer. They are actually designed specifically for this type of lug nut but work with most open end versions as well.

I have attached a review video for you.

expert reply by: Conner L

0

Answer 1

There is a great option for a hub cover that will work with the Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel #AM32424 but one does not come included with this combo. I recommend using the Phoenix USA QuickTrim Hub Cover…

view full answer...

Answer 2

It does sound like a possible overload situation. It is also possible that if you went up on a curb or something similar hard enough while loaded it could have caused the same problem. You will want to inspect the trailer suspension. You will be…

view full answer...

Answer 3

Some boaters actually swear by closed lug nuts as in general water is kept away from more of the wheel stud. With either setup though you still risk having problems that might cause a lug to break but I wouldn't necessarily blame your issue on…

view full answer...

Answer 4

The wiring configuration for the Cargo Towing Solutions HydraStar Electric-Hydraulic Actuator #HBA16 is listed in the instructions which are linked for you. The black wire connects to the 12V supply from the vehicle; the blue wire receives the…

view full answer...

Answer 5

If the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #QT545C will fit depends on the dimensions of the grease caps you have. The diameter of the interior at its narrowest point (nearest to the outside) is right around 2-1/4-inches, the depth…

view full answer...

Answer 6

All you have to do is follow the steps that you took to select and save each trailer setting on the Prodigy P3 #90195. Just hold down the boost button for 2 seconds until the "Select" menu comes up, scroll to the desired trailer, the press…

view full answer...

Answer 7

The Tekonsha Prodigy P3 Trailer Brake Controller part #90195 will draw 1 amp of current per volt sent to the trailer brakes on a tandem axle trailer and 1/2 amp of current per volt sent to the trailer brakes on a single axle trailer. Therefore, the…

view full answer...

Answer 8

The Wheel Masters Lug Nut Cover Pliers, part #WM8211, are designed to remove any size lug nut covers. Just pinch the lug nut cover with the pliers and pull the cover off.

view full answer...

Answer 9

I have attached a photo of how a breakaway system should be wired. If you would please, check the brake output wire on the trailer where the breakaway switch is spliced in. This is shown as the letter A in the attached photo. If something were to…

view full answer...

Answer 10

That fluid has to be going somewhere! What you can do is have someone activate the manual override on the brake controller in the vehicle cab while checking for leaks. Make sure the reservoir is full though. If it is not leaking at a line or…

view full answer...

Answer 11

There are 3 possible causes for the display reading - No Trailer Connected - on the Tekonsha P-3, Item #90195, when the trailer is connected. The first cause could be that you do not have the P-3 set up in the Hydraulic mode. On page 4 the…

view full answer...

Answer 12

Since you installed the P2, part #90885 and the #3014-P harness on your 2015 Jeep Cherokee, you should not have a burning plastic smell. This should be a very simple install. You did not say if the controller stopped working so I don't know if it…

view full answer...