How to Select Trailer Preset When Using the Prodigy P3 Brake Controller

Question

Question:

Retrieving Tekonsha Prodigy P3 trailer setting I understand how to save a trailer setting on the Tekonsha Prodigy P3 but how do I retrieve one? I can hold the boost, until the list of trailers comes up then insert the trailer number to save the current settings. No problem there. When I move from trailer 1 to trailer 2 how do I retrieve the saved settings for trailer 2?

asked by: Rick M

0

Expert Reply:

All you have to do is follow the steps that you took to select and save each trailer setting on the Prodigy P3 # 90195. Just hold down the boost button for 2 seconds until the "Select" menu comes up, scroll to the desired trailer, the press okay to use and also adjust those trailer settings.

expert reply by: Jon G

0

click to enlarge

Answer 1

The wiring configuration for the Cargo Towing Solutions HydraStar Electric-Hydraulic Actuator #HBA16 is listed in the instructions which are linked for you. The black wire connects to the 12V supply from the vehicle; the blue wire receives the…

view full answer...

Answer 2

I have attached a photo of how a breakaway system should be wired. If you would please, check the brake output wire on the trailer where the breakaway switch is spliced in. This is shown as the letter A in the attached photo. If something were to…

view full answer...

Answer 3

The Wheel Masters Lug Nut Cover Pliers, part #WM8211, are designed to remove any size lug nut covers. Just pinch the lug nut cover with the pliers and pull the cover off.

view full answer...

Answer 4

That fluid has to be going somewhere! What you can do is have someone activate the manual override on the brake controller in the vehicle cab while checking for leaks. Make sure the reservoir is full though. If it is not leaking at a line or…

view full answer...

Answer 5

If the Phoenix USA QuickTrim Hub Cover for Trailer Wheels #QT545C will fit depends on the dimensions of the grease caps you have. The diameter of the interior at its narrowest point (nearest to the outside) is right around 2-1/4-inches, the depth…

view full answer...

Answer 6

Yes, the Phoenix USA QuickTrim Hub Cover part #PXQT545BHS will fit the acorn style (closed end) 1.38" tall lug nuts on your trailer. They are actually designed specifically for this type of lug nut but work with most open end versions as well. I…

view full answer...

Answer 7

There are 3 possible causes for the display reading - No Trailer Connected - on the Tekonsha P-3, Item #90195, when the trailer is connected. The first cause could be that you do not have the P-3 set up in the Hydraulic mode. On page 4 the…

view full answer...

Answer 8

Some boaters actually swear by closed lug nuts as in general water is kept away from more of the wheel stud. With either setup though you still risk having problems that might cause a lug to break but I wouldn't necessarily blame your issue on…

view full answer...

Answer 9

The Tekonsha Prodigy P3 Trailer Brake Controller part #90195 will draw 1 amp of current per volt sent to the trailer brakes on a tandem axle trailer and 1/2 amp of current per volt sent to the trailer brakes on a single axle trailer. Therefore, the…

view full answer...

Answer 10

Yes, the Phoenix USA QuickTrim Hub Cover #QT545C will fit your 1/2" acorn style lug nuts. They are specifically designed to fit this style but also work with many open ended lug nuts as well.

view full answer...

Answer 11

There is a great option for a hub cover that will work with the Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel #AM32424 but one does not come included with this combo. I recommend using the Phoenix USA QuickTrim Hub Cover…

view full answer...