Weight of Demco DM04369 Replacement Hub

Question

Question:

HI, I was wondering if you could tell me what one of the wheel hub assemblies weighs? Item # DM04369 thank you in advance for your help.

asked by: Weston

0

Expert Reply:

The # DM04369 replacement hub for Demco Kar Kaddy, Tow IT II or Penske Tow dollies weighs in at 9 lbs. The hub has a 5 on 4-1/2 inch bolt pattern. I've linked to a product description video that you might find helpful.

expert reply by: Mike L

0

Answer 1

You can test that the hydraulic brakes on your Demco Kar Kaddy SS Tow Dolly #DM9713045 are working correctly by jacking up one wheel and chocking the other. Have a friend use a piece of wood to engage the surge brake actuator while you try to spin…

view full answer...

Answer 2

I went out to the warehouse and measured the Replacement Hub Assembly for Demco Kar Kaddy, Tow IT II, or Penske Tow Dolly #DM04369 from the gold piece rearward, and it measured 4-1/4" long.

view full answer...

Answer 3

It might be possible to add trailer brakes to your tow dolly but due to the age of it I can't give you the exact parts you'd need. You'd have to take your wheels and hubs off to check out and measure the spindle to determine…

view full answer...

Answer 4

The picture you submitted does show a trailer spindle that has a brake flange mounted to it. Based on that it is possible you could install brakes on your tow dolly. It really comes down to what spindle your trailer has though. That will dictate…

view full answer...

Answer 5

Yes, it is possible to put hydraulic disc brakes on a tow dolly. We do not offer a kit specifically to add disc brakes on your dolly, but I am happy to walk you through all the parts you will need. However, there are a couple of things we need to…

view full answer...

Answer 6

The lug nut size that the Demco Hub part #DM04369 uses are 12 mm which we offer with the part #DM02933.

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side.…

view full answer...

Answer 8

The long and short of it is that you need to route wiring from the cold side of the stop light switch (only gets hot when brake pedal is pressed) on your dinghy up to the location that you are mounting the RoadMaster Replacement LED Display Monitor…

view full answer...

Answer 9

I recommend replacing the entire brake assembly on your 3500-lb axle if the magnet is so badly corroded that it is now stuck to the actuating arm. We offer cost-effective brakes #AKEBRK-35R-SA and #AKEBRK-35L-SA that are rated appropriately for…

view full answer...

Answer 10

No, you will need to get the correct hub assembly for your spindle. If you are unsure of what hub assembly you need to use a digital caliper and measure your spindle to the thousandths of an inch where the bearings ride. You can use the photo…

view full answer...

Answer 11

If you have a 3,500 lb AL-KO axle and the brakes are indeed 10 inches, you can use Trailer Hub and Drum Assembly, #AKHD-545-35-K for a standard spindle and #AKHD-545-35-EZ-K for an E-Z lube spindle. For brakes you can use etrailer.com Trailer Brake…

view full answer...

Answer 12

We do actually have Dexter electric drum brakes in your required 10 x 1-1/2-inch size, parts #K23-473-00 and #K23-472-00, which are right- and left-hand, respectively. These are complete bolt-on (4-bolt) replacements that fit wheels diameters from…

view full answer...