Lug Nut Size that the Demco Hub # DM04369 Uses

Question

Question:

Two reviews mention that this hub has metric studs, while the old hub it replaces uses 1/2inch lug nuts. So I dont have to wait until this one arrives to measure and then order the proper lug nuts, it would be nice to know the exact size or have a link to the correct lug nuts to buy. Thanks

asked by: Alex

0

Expert Reply:

The lug nut size that the Demco Hub part # DM04369 uses are 12 mm which we offer with the part # DM02933.

expert reply by: Jameson C

0

Answer 1

It might be possible to add trailer brakes to your tow dolly but due to the age of it I can't give you the exact parts you'd need. You'd have to take your wheels and hubs off to check out and measure the spindle to determine…

view full answer...

Answer 2

No, you will need to get the correct hub assembly for your spindle. If you are unsure of what hub assembly you need to use a digital caliper and measure your spindle to the thousandths of an inch where the bearings ride. You can use the photo…

view full answer...

Answer 3

The #DM04369 replacement hub for Demco Kar Kaddy, Tow IT II or Penske Tow dollies weighs in at 9 lbs. The hub has a 5 on 4-1/2 inch bolt pattern. I've linked to a product description video that you might find helpful.

view full answer...

Answer 4

I went out to the warehouse and measured the Replacement Hub Assembly for Demco Kar Kaddy, Tow IT II, or Penske Tow Dolly #DM04369 from the gold piece rearward, and it measured 4-1/4" long.

view full answer...

Answer 5

The Replacement Inner Slide for Demco DA91 Actuators #DM12808-97 you have pictured is only designed to work with the Demco Hydraulic Trailer Brake Actuator #8759121 or DA91 if you go by Demco's part numbers. It has a 3" x 3" outer…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...