Does Load Range Affect Tire Chain Fitment?

Question

Question:

Hello. Im seeking a set of tire chains for my RV. Wheel size is 225/75R 16E. The E is throwing me for a loop. Can I just get a set of 225/75R/16 chains no E and will they work? Or are there specific chains I should be looking at for my RV? Thanks.

asked by: Aaron

0

Expert Reply:

The letter at the end of the tire size is the load range rating. This will not affect the fitment of your chains. I HIGHLY recommend using these chains # TC2319. They will be really easy to install! Be sure to check out the video I've included to help with the install!

expert reply by: Adam E

0

Answer 1

The Titan Chain Alloy Snow Tire Chains #TC2319 are a confirmed fit for your 225/75R16 tires. Since tire chains are designed to fit specific tire sizes and those tires have specific load ratings you should have no issues as long as you are within…

view full answer...

Answer 2

The chain link thickness is the difference between tire chains #TC2319 and #TC2519. The smaller TC2319 has 3.7mm links whereas the TC2519 has 5.5mm links. I checked the owner's manual for the 2007 Ford E-350 and it does require the use of…

view full answer...

Answer 3

Ok, so in regards to snow tire chains for any vehicle, they only require one chain per tire. So one pair of chains - a quantity of two chains - is all that is needed for putting chains on your 2002 Ford Explorer with 235/70-16 tires. I looked up…

view full answer...

Answer 4

You didn't tell me what tire size you do have, but chances are you have the 225/75-16 as both tire chains you mentioned are a fit for this size. Essentially both chain sizes will provide you with the same thing in terms of performance and…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If your 2020 Kia Sorento has the factory tow package, there will be a tail light wiring connector behind the rear tire of the driver side, on the outside of the frame rail. As shown in the attached photos, an underbody cover will need to be removed…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...