Lock for Demco A-Frame EZ Latch Coupler

Question

Question:

what is best lock for Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Black - 2 Ball - Bolt On - 10K Item # DM14793-81

asked by: Joe H

0

Expert Reply:

The lock I recommend for the Demco A-Frame EZ Latch Coupler # DM14793-81 is the etrailer Trailer Coupler Lock # e98887.

This lock is going to do a great job of keeping your trailer safe and sound and will work perfectly with the Demco latch.

expert reply by: Jameson C

0

Answer 1

Thank you for your purchase of the Demco Channel Tongue Trailer Coupler - eZ-Latch. The diameter is 5/16" and the lock that is designed specifically for Demco couplers with the eZ-Latch is the following: - InfiniteRule Lock for Demco…

view full answer...

Answer 2

For a 2 inch hitch ball that will work perfectly with the Curt Ball Mount #C45070 you mentioned I recommend the Tow Ready #63845. When installing the ball it should be torqued down to 250 foot pounds. I have attached a couple short video reviews on…

view full answer...

Answer 3

The wires of the Autowbrake Electric Brake Controller #3430001 are 14 gauge and were intended to be wired directly too a junction box where from there would run to all of the circuits of the trailer wiring. I would only run 18 gauge to lights and…

view full answer...

Answer 4

I do have an option for you Trevor but there is not a custom fit 7-Way harness available for the 2020 Subaru Outback Wagon. You will need to convert Tekonsha 4-Pole flat trailer connector part #118467 to a 7-way connector with part #ETBC7. The…

view full answer...

Answer 5

The Autowbrake brake controller part #3430001 that you referenced draws up to 15 amps. It's only going to draw amperage when the controller is activating the trailer brake so it would not be something you'd need to install an on/off switch on…

view full answer...

Answer 6

For the Demco EZ Latch Coupler like item #DM37ZR that does not have a lip around it you would want the Fastway Universal Trailer Coupler Lock item #DT25013KA. This is by far the best and most compatible option of the ones you listed. If you have more…

view full answer...

Answer 7

You are correct. Other than how they are made, the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K #DM37ZR and the #DM14793-81 have the same ratings and will work the same. There is no pro or con to either, so…

view full answer...

Answer 8

I went to our warehouse and pulled one of the Pro Series Trailer Jack part #PSRV20000103. I took some measurements and have attached a photo of the jack with the measurements noted. From the end of the handle to the outer tube on the jack it measures…

view full answer...

Answer 9

It sounds like you need to replace your trailer coupler as there should not be excessive up and down or side to side play on the hitch ball. If you do have too much play or the latching mechanism is not functioning properly like you said then you are…

view full answer...

Answer 10

The Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Black - 2" Ball - Bolt On - 10K #DM14793-81 is rated accurately. There are a few 2 inch hitch balls like the Curt #A-90 which is rated to support that capacity. I've copied the page…

view full answer...

Answer 11

The Demco A-Frame Trailer Coupler w/ Jack Hole #DM14793-81 that you referenced is a confirmed fit for a hitch ball with a 2 inch diameter. To couple or uncouple your trailer you will simply lift the eZ-Latch in the upward position. If you were having…

view full answer...

Answer 12

If you look at the diagram that I received from my contact at Demco, you can see several of the dimensions of the #DM14793-81 trailer coupler. If there were other dimensions you were needing, please let me know.

view full answer...

Lock for Demco A-Frame EZ Latch Coupler

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching