Which TorkLift Custom Frame-Mounted Camper Tie-Down For 2015 Ford F-350 DRW

Question

Question:

need torklift set for 2015 F350 dually 5000#, 3 slide camper. What do you recommend?

asked by: Scott R

0

Expert Reply:

For your 2015 Ford F-350 Dual Rear Wheel there are a few options depending on if you have the factory installed trailer hitch receiver, or an aftermarket trailer hitch receiver.

If you have a factory installed trailer hitch receiver you will need the TorkLift Front Custom Frame-Mounted Camper Tie-Downs # TLF2016 and Rear # TLF3006.

If you have an aftermarket trailer hitch receiver that is not made by TorkLift you will need the TorkLift Front Custom Frame-Mounted Camper Tie-Downs # TLF2016 and Rear # TLR3500. If you have a Torklift SuperHitch Original 20K you will need Rear # TLR3503, and if you have a Torklift SuperHitch Magnum 30k you will need Rear # TLR3504.

I also recommend the TorkLift Locking FastGun Turnbuckles # TLS9526-2-LK as they are a durable stainless construction that is corrosion resistant so you don't have to worry about them seizing up due to rust.

I included a few videos on the TorkLift Custom Frame-Mounted Camper Tie-Downs and the TorkLift Locking FastGun Turnbuckles for you to take a look at.

expert reply by: Samuel C

0

Answer 1

I went ahead and reached out to Torklift, and they confirmed what you need to in order to remove the gas tank cover on your vehicle to install the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLF2016. The cover drops down and gives you…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The two parts you mentioned (#RP87FR and #RP39FR) that fit your 2021 Ford F-350 Super Duty will both allow the ability to pull a gooseneck trailer with a gooseneck ball or use a 5th wheel hitch in the puck system. The only difference between them is…

view full answer...

Answer 8

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift P/N…

view full answer...

Answer 11

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 12

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...