Replacement Motor for Coach Step 32 Series on 2002 Fleetwood Heritage

Question

Question:

2002 Fleetwood Heritage motor coach 32 Series Step All of your info says that this is the replacement motor, however the gear does not match up to the teeth on my gear. I see no way to mount this unit to make it work with my step. Can you send me a drawing or any info to help me get this corrected. Can a technician call me and walk me through my concerns. 419-619-1122.

asked by: Al H

0

Expert Reply:

Based on your picture the replacement motor you need is actually the part # LC380073. This would explain why the # LC379608 that you referenced is not fitting at all.

expert reply by: Jameson C

0

click to enlarge

Answer 1

According to my contact at Stromberg Carlson, their #LG-179014 follower leg would indeed be an acceptable replacement for your Venture #900-40L if the 29-1/2 inch outer tube and overall heights of 33-1/2 match your existing jack. You can see these…

view full answer...

Answer 2

We can help you determine the correct replacement landing gear for your Monta Vista, though landing gear is a universal type of fit, and there isn't specific landing gear that fits your trailer. So in order to determine the correct…

view full answer...

Answer 3

I was not able to reference the part number "VMI900L" but in order to determine if the Replacement Follow Jack w/ Drop Leg part #LG-179014 is the correct replacement for you, you will need to measure the distance between the bracket…

view full answer...

Answer 4

For your Venture landing gear set the correct follower leg you'd need is the part #LG-179014 which matches what you sent in a picture of.

view full answer...

Answer 5

To determine the correct replacement landing gear for your 5th wheel trailer, you will need to measure the mounting brackets on your trailer from the underside of the top bracket to the top of the lower bracket as shown in the diagram. From there…

view full answer...

Answer 6

Sounds like the correct follower leg you would need is the #LG-179014 that you referenced. The overall length of the leg is 33-1/2 inches and the distance from the inside of the two brackets is 17-1/2 inches. Check out the picture I attached for…

view full answer...

Answer 7

You will either need to connect to your truck or have another stabilizer to support the weight when you remove the landing gear. The lead or follow leg can then be removed by loosening the welded brackets that hold the leg in place and move them…

view full answer...

Answer 8

When replacing the Motor #LC380073 on your Kwikee Revolution Steps #LC3725791 you need to use a jack or another object to hold the steps in the retracted position.

view full answer...

Answer 9

The exact diameter of the little 9-toothed gear on the Replacement Motor for Kwikee Revolution Series Electric RV Steps #LC380073 is 15/16 of an inch. I went ahead and included a diagram of the dimension for your convenience.

view full answer...

Answer 10

I spoke with my contact at Lippert who said that using the correct motor (part #LC380073) will help to fix the issues you are having with your Revolution Power Step #LC3725791 but you will also need to adjust your cams to remove some of that play you…

view full answer...

Answer 11

It sounds like you may have a power issue getting to the Steps #LC3725791 on your 2021 Winnebago Forza 36H RV Motorhome. On the steps you will have a 12 gauge red wire which runs to a 12 volt power source. There is also a 16 gauge yellow wire which…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Motor for Coach Step 32 Series on 2002 Fleetwood Heritage

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching