Will the etrailer Anti-Rattle Hitch Stabilizer for 2" Hitches Work On Any Brand Hitch

Question

Question:

Will it work on the BM hitch

asked by: Ed M

0

Expert Reply:

The etrailer Anti-Rattle Hitch Stabilizer for 2" Hitches part # e99007 isn't specific to any one particular trailer hitch brand. It will work with all 2" trailer hitches with a collar around the opening so if this is what you have then yes, it will work.

I don't have refrence to BM trailer hitches unfortunately.

expert reply by: Conner L

0

Answer 1

The B&W Silencer Pad #BWTS35020 is intended to be placed on the shank of one of their Tow & Stow Multi-Ball Mounts like #BWTS10048B so that it acts like a gasket between the collar on the end of the hitch's receiver tube and…

view full answer...

Answer 2

The B&W Tow & Stow 3-Ball Mount part #BWTS30048B is designed for a 3" receiver tube opening therefore if this is what you have on your 2006 Ford F-250 then yes, it will work for you. However, if I had to guess I would say…

view full answer...

Answer 3

I don't have a great answer for you because of the shank style the Thule T2 Pro XTR Bike Rack #TH23JV uses. The #TH23JV rack uses an AutoAttach system that does not allow for some adapters to work well. You would need to go with a hitch reducer…

view full answer...

Answer 4

I took measurements of the Anti-Rattle Hitch Lock for Malone Cargo Carriers #MPG2174 for you and the bolt length is 4-1/4" and diameter is 1/2". Included is a review video for additional information.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 8

Hello Steve. I do have a good solution for you, but I cannot recommend using the Malone Adapter #MPG544. Since it is rated for towing only 4,000 lbs, your 8,000 lb towed vehicle would be double the max towing capacity. You are right about there being…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Will the etrailer Anti-Rattle Hitch Stabilizer for 2" Hitches Work On Any Brand Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching