Replacement Scissor Jack for 2014 R-Pod Camper

Question

Question:

Im looking for an exact replacement for a leveling jack for a 2014 Rpod trailer. The jack model is Tristar 2500...please see attached photos. It looks very similar to the etrailer part #JSC-24-IND Unfortunately the mounting brackets are welded to the frame of the trailer, so Im hoping to just bolt the replacement to the existing brackets if possible. Please suggest the correct replacement part #. Thanks!

asked by: Dave

0

Expert Reply:

Thanks for the picture of your damaged scissor jack. Based on that the part # JSC-24-IND would be an exact replacement that you could attach to the same mounting plate you have currently.

expert reply by: Jameson C

0

Answer 1

The stabilizer jacks aren't trailer specific, but the mounting hole spacing is pretty standard across the board. I'd recommend removing the damaged jack and comparing the mounting plate hole spacing to what's shown in the…

view full answer...

Answer 2

It does appear that your 2016 R-Pod 178 uses the Ram scissor jack, #TJSC-24, so it would be the correct replacement. Should you also ever need a replacement handle it is #TJSC-24-HD.

view full answer...

Answer 3

The Scissor Stabilizer Jack #TJSC-24, which also comes in a 2-pack #TJSCHD-24 and a 4-pack #TJSCHD-24-4, is a universal fit so you would need to double check our measurements to ensure they fit your travel trailer. When they are collapsed they…

view full answer...

Answer 4

The actual height when the Scissor Jacks part #TJSC-24 is fully compressed is 5 inches and fully extended is 23-3/4 inches. You should note that these aren't designed to lift a vehicle or trailer off the ground as they are only for stabilization.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hello Gale. I can definitely point you in the right direction. Based on the pictures I can see online the 2016 Rpod 179 appears to use a horizontal single tank regulator. Our best option to replace this is the JR Products Horizontal 2-Stage Propane…

view full answer...

Answer 7

I am attaching a photo of the mounting locations on the Ram Scissor Stabilizer Jack #TJSC-24 that I believe you were referencing. They are from the edges of the mounting holes but I believe your mounting hole locations would match up just fine. Let…

view full answer...

Answer 8

I went to our warehouse and measured the Leveling Scissor Jack #JSC-24-IND. The bolts on the #JSC-24-IND are 2 inches apart center to center, just like they are in your photo. When closed, the stand measures 4 inches from the base to the top of the…

view full answer...

Answer 9

Many times the thickness of the grease seals #RG06-070 is not a factor. If this is a trailer hub there should be enough room for the seal to fit flush with seal flange.

view full answer...

Answer 10

For a replacement jack for your 2021 Jayco Jay Flight SLX 7 174 BH I recommend the Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs #TJ01RT. This jack same mounting hole dimensions as your current jack at 3 inches apart on center.…

view full answer...

Answer 11

We have had someone tell us the swivel fittings that particular hose won't fit in the 4 inch bumper of your trailer, and the manufacturer said they could grind down two of the lugs and the hose would then fit. We do have a video which I've…

view full answer...

Answer 12

Even when stored in the somewhat controlled environment of a garage, tires are still subject to dry rot and flat spotting. Even if the tire tread has plenty of depth left and you can't see any cracking with the naked eye, the generally accepted…

view full answer...

Replacement Scissor Jack for 2014 R-Pod Camper

Product Page this Question was Asked From

Continue Researching