Anti-Rattle and Hitch Lock Recommendation for Ball Mount with Solid Shank

Question

Question:

I have a solid shank and need to reduce the rattle/movement.

asked by: Craig P

0

Expert Reply:

Since there isn't a anti-rattle hitch lock combo that fits solid shank ball mounts you'd need to go with separate items to accomplish both. The part # GY88XR fits really tight so it would not be my first choice as it is known to be challenging. Instead, I'd use the part # e99007 which will fit much easier and work better overall as well.

Then for a hitch lock you could use the part # BD580400 and you'd be set.

expert reply by: Jameson C

0

Answer 1

In order to determine the maximum gross trailer weight (GTW) that you can haul with your 2016 Chevrolet Traverse, you will need to find both the gross combined weight rating (GCWR) and the gross vehicle weight (GVW). If you subtract the GVW from the…

view full answer...

Answer 2

For safe operation of the Channel Style Adjustable Ballmount #C45900 Channel Style Adjustable Ballmount the set screw isn't absolutely required, but it would be recommended since it will reduce movement of the ball mount.

view full answer...

Answer 3

The Curt Channel Style Adjustable Ballmount - 2" & 2-5/16" Balls - 14,000 lbs #C45900 has an overall tongue weight capacity rating of 1,400 lbs. This may be further limited however by your trailer hitch receiver tongue weight capacity,…

view full answer...

Answer 4

Yes, the B&W Tow & Stow 3-Ball Mount #BWTS10049B that you referenced will fit your 2002 Ford F-350 without any problems. It's designed to fit 2 inch hitches like what your truck has as well. I attached a picture of it installed on a…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 11

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 12

Hey Buddy, so the Fastway Adjustable Ball Mount part #DTSTBM6825-2S is a really great choice for the 2-1/2 inch hitch of your 2021 Ford F-250 which is going to be very solid in your hitch due to it's built in anti-rattle device that is easy to…

view full answer...