Custom Gauge Pillar for the Gauge for Air Lift Suspension on a 2006 Ford F-350 King Ranch

Question

Question:

2006 F350 DRW King ranch. Where do i get custom pillar or dash pod for installing gauge.

asked by: Richard

0

Expert Reply:

The gauge size in Air Lift kits like # AL25856 is designed to fit most custom pillar pods or dash mounts but they do not offer custom pillars or pods. The kits do come with a small pad the gauge fits in that can be mounted on the dash. For a 2006 Ford F-350 you can use Air Lift system # AL57212. A company called AutoMeter makes some custom gauge pillars that might work for you.

expert reply by: Michael H

0

Answer 1

If you are talking about adjusting the height of your 5th wheel hitch like the Curt A20 #C16140 then you will simply need to move the hitch head to the appropriate adjustment holes (see attached picture). Loosen the nuts on the bolts holding the…

view full answer...

Answer 2

The legs of the Curt A20 5th Wheel Trailer Hitch - Dual Jaw - 20,000lbs Item #C16140 have a simple pin and clip to attach to the bed rails. If the clips have been pulled and the pins are too tight to get out I recommend using some WD40 and trying to…

view full answer...

Answer 3

Since you mentioned the cotter pins which are used to secure the feet inside the rails, that makes me that you are referring to the connection point between the rail and foot on one of the four corners of the Curt A20 5th Wheel Trailer Hitch part…

view full answer...

Answer 4

I can help you with info on greasing the A20 hitch but we don't have a video to share at this time. The zerk fittings for the Curt A20 hitch part #C16140 are located on the front of each jaw.The jaws must be in the closed and locked position for…

view full answer...

Answer 5

There aren't any air compressor systems designed specifically for the Air Lift LoadLifter 5000 Ultimate Plus Air Springs. These air springs will use the same air compressor kit as any other air springs. There are fittings that come with the air…

view full answer...

Answer 6

You can install a 5th wheel hitch with your AirLift LoadLifter 5000 air bags but the frame brackets on the 5th wheel installation kit part #RP30073 will interfere with the mounting location on the AirLift part #AL57212. Therefore, it is not…

view full answer...

Answer 7

For your 2006 Ford F-250 the Air Lift kit you would want is the part #AL57212 since you do not have a fifth wheel or gooseneck hitch. This has been confirmed as a fit for your vehicle and would provide you with additional rear suspension support. The…

view full answer...

Answer 8

When wiring up the Air Lift WirelessONE Compressor System for Air Helper Springs - Remote and Mobile App #AL25980EZ the power wire needs at least 15 amps to power the unit and the keyed power source that runs to the ignition switch circuit needs at…

view full answer...

Answer 9

Sounds like you may have ran the power wire of the Air Lift Compressor kit part #AL25980EZ to a keyed power source instead of to the vehicle battery so when you turn the vehicle off the compressor loses all power and upon start up resets. The red…

view full answer...

Answer 10

I reached out to Air Lift about your Air Lift WirelessONE Compressor System #AL25980EZ and the first thing you should try is unplugging the fuse at the battery for a few minutes in order to reset it. If that does not solve the problem then you will…

view full answer...

Answer 11

For an air bag kit that is available for your 2006 Ford F-350 4x4 you would want the Air Lift part #AL57212. The #F2398 is not a fit for the 4x4 models and would not work for you.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...