Brake Controller Connector Location 2017 Ford F-150

Question

Question:

We here is the plug under the dash for the brake controller located

asked by: Rodney

0

Expert Reply:

The brake controller connector is clipped to the rear of the small storage pocket just to the right of the steering column as shown in the linked video. The video shows how to access the connector.

If you're using a Tekonsha brake controller like the # TK90160, you'll need the # 22292 wiring harness.

expert reply by: Mike L

0

Answer 1

On your 2017 Ford F-150, it sounds like you have an adapter like the Hopkins #37185. The orange and blue wires you splice into are the power and brake controller output wires. You are correct that the remaining wire is your reverse light signal…

view full answer...

Answer 2

It sounds like you are connecting wires to an aftermarket 7-way on your 2017 F-150. There are two wires run from under the hood to the end of the driver's side frame rail. One is a blue wire which is the electric trailer brake output wire…

view full answer...

Answer 3

In order to install a 7-way trailer connector on your 2017 Ford F-150, you are first going to need to install a 4-way trailer connector and then a 4 to 7-way trailer connector. For this, I recommend using the Hopkins Plug-In Simple Wiring Harness…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Brake Controller Connector Location 2017 Ford F-150

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching