Replacement Air Spring for Firestone Ride Rite Kit that Fits 2016 Coachmen Leprechaun

Question

Question:

Hello, I am looking for replacement rear air springs for a Firestone Ride Rite system on our 2016 Coachman Leprechaun Ford E-450 311FS. Can you help me identify which ones would be appropriate? Thank you!

asked by: Melissa

0

Expert Reply:

The correct air spring for the Firestone Ride Rite kit that fits your 2016 Coachmen Leprechaun is the part # F6397 since your RV uses the kit part # F22ZR.

expert reply by: Jameson C

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 7

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 8

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 9

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 10

Yes, the Curt hitch part #C77ZV is a fit for the 2023 Toyota Crown Hybrid. I attached a link to the install instructions as well as a link to an installer finder in case you wanted to find someone near you to install the hitch.

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...