Can A 2006 Chevy TrailBlazer Be Dolly Towed

Question

Question:

Can a 2006 Chevy trailblazer be towed on a tow dolly? If so do I put front wheels or back wheels on tow dolly. What is part number of tow dolly you recommend. Thank you

asked by: Jeff G

1

Helpful Expert Reply:

Yes, the 2006 Chevrolet TrailBlazer can be towed on a dolly. If you have a four wheel drive model then you will need to lift the front wheels. If you have a two wheel drive model then you will need to lift the rear wheels. If you have an all wheel drive model then you cannot dolly tow. The best tow dolly we have for this vehicle is the Demco Kar Kaddy X Tow Dolly part # DM9713093 due to both wheel size and weight constraints.

expert reply by: Conner L

1

Answer 1

Yes, we will have all the components you will need to be able to flat tow your 2022 Chevrolet Blazer. First you will need to select the correct baseplate. The Roadmaster Direct-Connect Base Plate Kit #RM28VR will only fit the 2.0L turbo engine…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 10

I have a set that will work however your 2023 Chevy Suburban's owners manual says not to use tire chains because of clearance issues on the inner part of the tires. You can find this information on page 370. To avoid damaging brake lines and…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...