Recommended 2K Timbren Axle-Less System to Add Brakes to Trailer in the Future

Question

Question:

I dont have brakes for my trailer right now cause theyre not needed but Can I get brake plates to add at a later time to these ASR2000S01? Budget costs

asked by: Mark W

0

Expert Reply:

The Timbren Axle-Less Trailer Suspension System # ASR2000S01 doesn't come with brake mounting flanges and although you can upgrade them at a later time, it would be more cost-effective in the long run to go with the system # ASR2000S02 instead which comes with a spindle set that already has the brake mounting flanges.

Attached is a link to our selection of hubs (and hub/drums) that will fit these spindles, as well as our brakes that work with these, and some helpful articles on trailer brakes that you can check out when the time comes to add brakes to your trailer.

expert reply by: Jon G

0

Answer 1

When using an idler hub or a hub and drum with brakes on the Timbren Axle-Less Trailer Suspension System, part #ASR2000S02, the difference in the distance from the bracket to the front face of the hub as shown in the attached drawing would be the…

view full answer...

Answer 2

We do offer some complete axle/hub/brake kits such as #35545E-ST-89 from Dexter, but we do not have a complete kit with the exact combination of features you require. We do offer 72-inch axles with 58-inch spring seats and idler hubs in your 4-on-4…

view full answer...

Answer 3

The Timbren Axle-Less Trailer Suspension System part #ASR2000S02 does not come with idler hubs but they can be added using the Dexter Trailer Idler Hub Assembly part #84545UC1-EZ.

view full answer...

Answer 4

You are indeed right to think this way. When picking out the appropriate leaf springs for your custom built trailer you will want to choose them based on what the actual loaded weight of the trailer will be. Just make sure that the leaf springs have…

view full answer...

Answer 5

The Timbren Axle-Less Trailer Suspension #ASR2KHDS09 you're looking at is actually not going to work with your trailer tires since this kit is only going to work with trailer wheels that are 16" or larger. So, instead I'd recommend going…

view full answer...

Answer 6

Yes, the Kenda Karrier ST175/80R13 Radial Trailer Tire #AM31990 will indeed fit on the etrailer Hitch Mounted Spare Tire Carrier #e98ZR. The spare tire carrier will work with virtually any 4 lug, 5 lug or 6 lug wheel. The #AM31990 wheel uses the…

view full answer...

Answer 7

For your snowmobile trailer I recommend going with a Timbren Axle-Less system such as #ASR2000S01. I have included a link to all the options rated for 2,000 pounds. The benefit is that you won't have an axle beam to rust and you still get the…

view full answer...

Answer 8

Thanks for the picture! I attached a couple of diagrams below for the Timbren Heavy-Duty Axle-Less Trailer Suspension item #ASR2KHDS02. These dimensional renderings with measurements will be able to give you the exact information you are looking for.…

view full answer...

Answer 9

I spoke to my contact at Timbren and he said the deflection or amount of travel for the Timbren Axle-Less Suspension System #A20RS545 is 1-3/4 inches. The clearance between the spindle support and the trailer frame when fully compressed will vary…

view full answer...

Answer 10

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 11

Even though it is not a fit for it, it is not impossible to install the #C92UR Trailer Hitch Receiver on a 2019 Honda Civic Si. However, in order to do this, you will need to remove the center mounted exhaust pipe. I have attached a few photos for…

view full answer...