Solution for Hitch Install Where Weld Nut Broke in Vehicle Frame
Question:
Hi, I was installing the hitch and the was applying torque to the smaller fasteners which require torque of 48 lb per instructions, it was reaching the required torque but it came loose and the fastener now just keeps spinning. I took the fastener out and noticed that the fastener had metal of the frame around it. The thread where the fastener goes in is damaged. What can I do now?
asked by: George M
Expert Reply:
Sounds like you broke the weld nut in the trailer frame of your vehicle as you were torquing the hitch bolts down. Normally this doesn't happen but if the torque wrench used is out of calibration it's easier to do. One solution would be to weld the weld nut back in place so you can tighten the nut or you could fishwire in new hardware.
I attached a video that demonstrates fishwiring for you to check out. I also attached a link to a page with all of our bolt leaders we offer as well.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Replacement Hardware Kit for Trailer Hitches
- Search Results: square hole spacer
- Q&A: Replacement Hitch Installation Hardware Kit for Curt Class III Hitch C13068
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
- Q&A: Comparison Between Curt C13427 and etrailer e95ZR Hitches for 2021 Hyundai Palisade
- Video: Cleaning Weld Nuts for Trailer Hitch Installation
- Video: Draw-Tite Hitch Anti-Rattle - Standard Anti-Rattle - 63080 Review
- Video: Review of Draw-Tite Trailer Hitch Ball Mount - Fixed Ball Mount and 2 Inch Ball - DT49MR
- Video: Draw-Tite Ball Mount Review DT49MR
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: ball
- Shop: Mounting Bracket 4-Pole Flat
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Shop: Vehicle Tow Bar Brake System
- Video: Weld Nut Removal and Replacement Review
- Q&A: Troubleshooting Hitch Install Bolts Not Threading Into Frame Rail Weld Nut
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: hitch
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Article: Trailer Wiring Diagrams
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: My Trailer Hitch Doesn't Fit
on Trailer Hitch
