Recommended Trailer Axle and Complete Suspension System for 2K Trailer

Question

Question:

I am looking for a trailer axle and spring kit. Do you sell them? I am looking for one that has the 48 center of leaf and 60 hub to hub. I would like something around 2500lb but 2000 is ok. I see leaf springs and then axles but nothing sold as a matching kit.

asked by: Jeffrey L

0

Expert Reply:

We have kits and parts, but not everything kitted like you are seeking but I can absolutely help you with that.

I recommend starting with the Dexter Idler Trailer Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,000 lbs # 20545I-EZ-60-10 or the 4 on 4 inch hubs # 20440I-EZ-60. Then you can use U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts # APUBR-10 to attach the axles to the leaf springs.

For your suspension, I recommend you get the Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear # APS2 and leaf spring (x2) # e84SR.

I've attached some videos and a couple articles on location to assist.

expert reply by: Jason S

0

Answer 1

I can confirm that the parts listed below are all compatible. I do recommend replacing your spring hangers since you are upgrading everything else on your suspension. The Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall…

view full answer...

Answer 2

The closest axle we have to your measurements is #CE33201GA-HUB which has a hub face of 57-1/2 inches and spring center of 46-1/2 inches. So it's very close. I'd double check your measurements to see if this will fit. The axle also includes…

view full answer...

Answer 3

I do have an option for you but the Dexter Over Under Conversion Kits are only available for 2-3/8" and 3" diameter axles and I don't think you will have either one of them due to the trailer being so small. That said, we still do have…

view full answer...

Answer 4

Yes we can get over or under slung axles. It would be very similar to the Dexter Idler Trailer Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs part #20545I-EZ-60-10 but you would have them custom make it with the spring…

view full answer...

Answer 5

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 11

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...