Recommended Hitch and Wiring for my 2019 Hyundai Elantra GT N-line?

Question

Question:

I noticed several other hitches specifically exclude the N-line trim because of the dual exhaust, however Im not seeing anything here that mentions that trim. If its a hard no wont fit, is there one in the works? Thanks

asked by: Marshall H

0

Expert Reply:

Yes the Draw-Tite Sportframe Trailer Hitch Receiver part # 24905 is a fit for your 2019 Hyundai Elantra N-Line. This is the only hitch compatible with the dual exhaust.

If you will require wiring use the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118692 this is the only harness that will not require yo to splice into your factory wiring.

expert reply by: Randy B

0

Answer 1

The only exceptions to the fitment of the Draw-Tite Sportframe Trailer Hitch Receiver #DT75MR on a 2023 Hyundai Elantra are the N Line and Hybrid models. Since your N model is neither one of these you'll be good to go! Keep in mind that this…

view full answer...

Answer 2

For your 2018 Hyundai Elantra GT, I recommend using the Curt T-Connector Vehicle Wiring Harness part #C56233 which is currently the only plug and play wiring harness we have for this vehicle. The install photos which you can see in the attached…

view full answer...

Answer 3

The Draw-Tite Sportframe Trailer Hitch Receiver #24905 is confirmed to fit all the 2018 Hyundai Elantra GT trim levels, unless the car was manufactured in Korea. You can verify this by inspecting the build sticker in the door jamb or if the 2nd…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...