2 Inch Diameter Hitch Ball with Long Shank

Question

Question:

I need a 2 hitch ball with a 1 diameter shank that is 3 long.

asked by: Jake

0

Expert Reply:

We have the Long Shank Hitch Ball, # C40020, that has a 2 inch hitch ball and a 3 inch shank and a towing capacity of 6000 pounds.

Another option is the Hidden Hitch Long Shank Ball, # 63849, which has a 3-3/8 inch long shank and 7,500 lb capacity.

Finally you could use the Tow Ready Long Shank Hitch Ball, # 19255, that you mentioned. This ball has a 3-3/8 inch shank and 3,500 lb capacity.

expert reply by: Robert G

0

Answer 1

Although not always necessary, it is always a good idea to upgrade the vehicle for towing a heavy load for an extending period of time. In order to tow a 16' camper that weighs roughly 2,500 lbs. when dry, with a 2005 Dodge Grand Caravan, I…

view full answer...

Answer 2

There are a couple of options on tightening the nut on a ball installed at the end of Swagman towing bike carrier #S64675. First, if the nut is the same width as the opening at the end of the carrier then the walls of the shank will prevent the nut…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

2 Inch Diameter Hitch Ball with Long Shank

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching