Troubleshooting Trailer Hitch Receiver Bolts That Won"t Install in Factory Weldnuts

Question

Question:

i have a 2013 chevy equinox. i bought a etrailer hitch from you and the bolts wont fit in the weld nuts. could it be possible they are too big.

asked by: Gene A

0

Expert Reply:

For your 2013 Chevy Equinox, the # e98865 you bought (according to the invoice associated with your email) is the correct fit. It is a fit for 2005 to 2017 models so it is likely there is either grime in the weldnuts or powder coat overspray that is in the threads that needs to be cleaned up. I don't think the bolts are too big... which should be M12-1.75 x 40mm.

I've attached a help article on cleaning the weldnuts to assist.

expert reply by: Jason S

0

Answer 1

Due to the age of your vehicle, there is an excellent chance that there is a significant amount of corrosion and road grime built up in the weld nuts in the frame of your Chevy Equinox. This build up is what is preventing the bolts from threading…

view full answer...

Answer 2

I'm sorry to hear about the trouble that you have with the installation! From the looks of the picture, it looks like the bracket of the #e98859 does not completely line up with the hold on your frame. To fix this issue, one of the best solutions…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...