How to Add Longer Crossbars to 2016 Chevy Traverse with Factory Crossbars

Question

Question:

I have a 2016 Chevy traverse with factory installed side rails the run front to back. I currently have the factory cross bars but would like some extra room. Is there any setup that would allow me to put 8 or 60 inch crossbars on the roof using the factory installed rails? Thanks. You guys are the most knowledgeable staff!!!

asked by: Craig

0

Expert Reply:

I have an option that will allow you to install longer crossbars on your 2016 Chevy Traverse, but we don't have a roof rack that would use your factory flush rails for the attachment points.

The solution would be to use the Rhino-Rack Custom DK Fit Kit # DK297, along with the Rhino-Rack 2500 Series Legs # RRRLKVA. This system would bypass your factory rails, and fit over them, using a clamp-style attachment to secure itself onto your vehicle's roof.

With those in place, you can choose between the following crossbars:

Rhino-Rack Vortex Aero Crossbar 54" - # RRVA137B-2
Rhino-Rack Vortex Aero Crossbar 65" - # RRVA165S-2
Rhino-Rack Vortex Aero Crossbar 71" - # RRVA180S-2

expert reply by: Carla M

0

Answer 1

The Roadmaster dual hitch adapter part #RM-077-2 that you referenced was designed for your current situation. It allows you to carry a bike rack in the upper hitch opening and tow a vehicle with the lower hitch opening. This has the weight capacity…

view full answer...

Answer 2

It doesn't appear you would be able to fit a 4 bike rack in between your 2019 Acura MDX and the camper and still be able to make a some what sharp turn. I recommend looking in to adding a hitch to the back of the trailer like the Curt Adjustable…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 7

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 8

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 9

Brien, it sounds like you did your research so kudos to you, but the awning you're looking at is not going to work with the wind sensor. You'd need to use the Solera Smart Arm 12V Power RV Awning #LC517517 instead. You're also going to…

view full answer...

Answer 10

Hi Joe, The Blue Ox Base Plate Kit #BX1139 is a confirmed fit for your 2024 Jeep Wrangler Rubicon X per Blue Ox. I don't currently have an installation video on a model with a steel bumper but I did measure from the mounting holes down to the…

view full answer...