How To Obtain 60" Hitch Extension for 2011 GMC Sierra 2500/3500 for Towing with In-Bed Camper

Question

Question:

I need a 2 1/2 tow hitch extension 60 long for a 2011 GMC Sierra Diesel Dually. I want to tow a 18 boat behind a Lance 1161 truck camper total weight boat/trailer is about 3,500 lbs. What are my options?

asked by: David N

0

Expert Reply:

The only trailer hitch extension available in a 60" length is the TorkLift SuperTruss Hitch Extension part # TLE1560 which then must be used with the TorkLift SuperHitch Original Trailer Hitch Receiver part # TLC1209 for models with 6-1/2' bed or part # TLC1208 for 8' long beds. That said, this is going to be your only option. It will provide you with a 5,000 lb gross trailer weight rating. You'll also need the TorkLift Wiring Harness Extension part # TLW6060.

expert reply by: Conner L

0

Answer 1

According to my contact at TorkLift, the 18" wheels that come with 275/65r18 tires on a 2016 Ford F-350 are the largest tires they have confirmed will fit with the TorkLift #TLF1002-30 installed. They also mentioned that a 275/65r20 tire, which…

view full answer...

Answer 2

The Air Lift LoadLifter 5000 Ultimate Air Springs w/ Internal Bumpers #AL88338 are the air bags I recommend using for your 2011 GMC Sierra 2500HD with the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1012. These air springs will come…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...