Replacement Black Cover for RAM/etrailer Electric A-Frame Jack

Question

Question:

It’s on my camper jack. The jack works, should just need the cover

asked by: Dustin M

0

Expert Reply:

If you can reply to this email with the pictures I can help you out. Just be sure to let me know what the product is they are installed on!

expert reply by: Jon G

0

click to enlarge

Dustin M.

5/13/2020

It’s on my camper jack. The jack works, should just need the cover

Reply

Jon G.

5/13/2020

Thanks for the pictures! The Electric Jack w/ Footplate and 7-Way Plug # EJ-3527-BBX is what you have and so the replacement cover is part # EJ-3520-BCV. Please note that this doesn't come with the switches so you'll want to keep those when you replace the cover. If the switches need to be replaced too then you'll need part # EJ-3520-PSW for the power and part # EJ-3520-LSW for the light.

Reply

Answer 1

The Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX uses a 7-way RV-style plug. I have included a diagram that shows the pin-out for RV style 7-way plugs. This will show you what each pin does. I have also listed the functions below and linked…

view full answer...

Answer 2

The Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX that you referenced has a height of 20-1/2 inches from where it mounts to your trailer frame to the top of the jack.

view full answer...

Answer 3

If you take a look at the diagram I've provided for the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW which goes to the Electric Jack w/ Footplate #EJ-3520-WBX, you'll be able to see how both of the…

view full answer...

Answer 4

I have attached a photo you can use to connect the Replacement Power Switch #EJ-3520-PSW to your 3,500 lb RAM jack. We don't have a direct wiring diagram but if you notice even though the wires are the same colors they look pretty different so…

view full answer...

Answer 5

If you check out the picture I attached you can see how the wires of the Ram jack switch #EJ-3520-PSW are supposed to be ran to it.

view full answer...

Answer 6

RAM jacks provided the attached photo showing how the various single and doubled wires connect to the pins on the back of the power switch #EJ-3520-PSW. They do not offer a separate wiring diagram.

view full answer...

Answer 7

The replacement power switch for your Ram Electric Jack Item #EJ-3520-BBX is Item #EJ-3520-PSW. Links to additional information attached.

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...