Replacement Pull Pin for Yakima HoldUp (2008-2009) Bike Rack 8002419

Question

Question:

I need a replacement spring pin for a Yakima Holdup +2 2008-2009 hitch tray bike rack. This part this part Y90175 looks very much like my current spring pin. BTW, its stuck so I cant remove to take a picture without potentially damagin it. Does this part Y90175 work for this bike rack? If not, do you carry the right spring pin for this bike rack?

asked by: Paul K

0

Expert Reply:

We do have the replacement part you need, though it is different than the part you mentioned.

For your Yakima HoldUp (2008-2009) Bike Rack 8002419, the correct replacement pin is the Replacement Stabilizer Pull Pin for Yakima HoldUp Tilting Bike Racks # Y39FR.

I confirmed this with Yakima for you.

expert reply by: Kyle S

0

Answer 1

Here are the measurements for the Replacement Pull Pin for Yakima HoldUp Bike Racks item #Y39FR. Diameter: 5/8" length: 5-3/8"

view full answer...

Answer 2

Thank you for the photo of your older Yakima hitch bike rack for which you want to confirm the fit of replacement shank/tongue assembly #8880580. Yakima confirmed the fit of this part on your rack. You may also need Hitch Bolt #8890200 to secure the…

view full answer...

Answer 3

Sounds like you are looking for the replacement pull pin part #Y39FR for your Yakima Holdup bike rack.

view full answer...

Answer 4

You'll need to do just a bit of measuring to determine if you can use the Yakima LockNLoad Platform Rack for Crossbars - 55" Long x 49" Wide #Y05044-39. I have added diagrams from Yakima below that show you exactly what to measure and…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...