Torque Specs for Curt Trailer Hitch 13251 for a 2005 - 2010 Jeep Grand Cherokee

Question

Question:

What is the torque down setting?

asked by: Jaime B

0

Expert Reply:

The Curt Trailer Hitch Receiver part # 13251 which is a fit for a 2005 - 2010 Jeep Grand Cherokee currently has a torque spec rating of 110 ft. lbs. That said, these torque spec ratings can change so it is always best to check the most up to date version of the online owner's manual. If you need a torque wrench capable of this figure, the Powerbuilt Beam-Type Torque Wrench part # ALL644044 will work perfectly.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

I'm not sure why they include that replacement latch but that is not required for any of the aftermarket hitches or wiring. It is probably something related to the installation of the OEM hitch. The etrailer #e45ZR you referenced is what I would…

view full answer...

Answer 12

To add a hitch to your 2024 Jeep Grand Cherokee L, I recommend the Draw-Tite item #DT42GR. This hitch is custom fit and bolts to your Jeep with included hardware. This is a class III hitch with a 2" receiver. It has a 7,500 lbs towing capacity…

view full answer...