Is There a Set of Torklift Tie Downs that Fit 2004 Toyota Tacoma

Question

Question:

Is there a brophy clamp style that will work on the 2004 Toyota Tacoma? Not the torklift style. Was your information helpf

asked by: Tom G

1

Helpful Expert Reply:

We have a set of Torklift camper tie downs that fit the 2004 Toyota Tacoma with the part numbers # TLT2306 and # TLR3500.

expert reply by: Jameson C

1

Tom G.

3/25/2020

Is there a brophy clamp style that will work on the 2004 Toyota Tacoma? Not the torklift style. Was your information helpf

Reply

Jameson C.

3/25/2020

Brophy has told us their clamp on style tie downs part # HSBP would work with your 2004 Toyota Tacoma. For hardware then you'd also need the # TDHP.

Reply

Answer 1

For your 2003 Toyota Tacoma I recommend the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front - Item #TLT2306 and TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear - Item #TLR3500 I also recommend getting TorkLift SpringLoad XL Turnbuckles…

view full answer...

Answer 2

The air springs used in Firestone Ride-Rite kit #F2407 for your 2011 Toyota Tacoma Pre Runner have a maximum diameter of 6.60 inches. They will be centered on the leaf spring stack. The lower bracket will be offset closer to the wheel. The upper…

view full answer...

Answer 3

For what you are looking for the TorkLift StableLoad Rear Suspension Upgrade w Quick-Disconnects #TLA7311 would work great for your 2012 Toyota Tundra. According to tests by Torklift these reduced side to side sway, porpoising, and body roll on…

view full answer...

Answer 4

Yes, you can use the TorkLift StableLoads like part #TLA7311 with aftermarket sway bars. The two products are far enough away from each other they would not interfere in any way. While the picture I attached may not be a Sprinter like your 2014 model…

view full answer...

Answer 5

Yes, you will need to drill into the leaf springs on your 2022 Ford F-250 Super Duty whether you go with the standard TorkLift StableLoad #TLA7311 or the Stainless Steel version #TLA7311S. I checked with TorkLift and it looks like you'll need to…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Hey Tom, the #ETBC7 kit is exactly what you will need to install a 7-way on your 2004 Toyota Tacoma TRD V6 with the factory 4-flat plug. Here are the answers to your questions: 1. Yes. The kit includes quick splice connectors which make this easy. I…

view full answer...

Answer 11

Your Tekonsha Prodigy P3 #90195 on your 2004 Toyota Tacoma is showing no trailer connected because you only have the 5-Way flat connector on your trailer. The 5-Way carries the basic trailer light functions and that 5th pin is typically for the…

view full answer...

Is There a Set of Torklift Tie Downs that Fit 2004 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching