Torklift StableLoad Rear Suspension Enhancement Recommendation for 2012 Toyota Tundra 8.1 ft body

Question

Question:

Have airbags and only have to apply 35-40 psi for 1400 hitch wt. I would like the kit to help in the Rockies sharp turns and uneven roads. Your input ! I may upgrade to a 1750 lb hitch load due to a bedroom slider unit 5th wheel and i I would definitely would like them on @ that change. Here again, yr input ! thanks

asked by: Al O

1

Helpful Expert Reply:

For what you are looking for the TorkLift StableLoad Rear Suspension Upgrade w Quick-Disconnects # TLA7311 would work great for your 2012 Toyota Tundra.

According to tests by Torklift these reduced side to side sway, porpoising, and body roll on vehicles they were installed on when towing. They also were shown to have worked better than air suspension enhancement.

expert reply by: Jameson C

1

Answer 1

The W217602445 part number you listed is our part #F2445 and would be the correct kit for 2007-2015 (current models as of August 2015) Toyota Tundras. Since you have a 6 inch lift kit the part #F2374 would be the correct spacer kit to use. I attached…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 5

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...

Answer 8

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Answer 9

The only difference between the HydraStar Disc Brake Kit with Actuator for Tandem Axle Trailers - 7K part #HSE7K-T1SO and part #HSE7K-T1 is that the latter comes with the hub which is integrated into the rotor. The former does not come with a hub and…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

For your 2023 Coachmen Pursuit 31BH you will need the Front SumoSprings Rebel Custom Helper Springs #SSF-170-40-2 and Rear SumoSprings Maxim Custom Helper Springs #SSR-184-40-1. If you were to select only one to install first I recommend the rear…

view full answer...

Torklift StableLoad Rear Suspension Enhancement Recommendation for 2012 Toyota Tundra 8.1 ft body

Product Page this Question was Asked From

Continue Researching